Bedienungsanleitung Proxxon FET (Seite 17 von 24) (Englisch)

782211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1. To adjust the angle, release knurled screw 4 and

set the desired value at the scale 5. Retighten

knurled screw 4. Adjust position of limit stop strip

1 and clamp firmly by tightening the knurled screw

2. Caution! Make sure at all costs that the limit stop

strip 1 is correctly seated in the receiver of the

angle stop 2 and that there is sufficient distance

from the end of the limit stop strip to saw blade 7!

In all cases: Switch off the saw and disconnect the

mains plug and test to see that the limit stop strip

does by no means touch the saw blade or the saw

blade guard, see fig. 13c!

3. Insert clamping piece 8 in the guide of the limit

stop strip (fig. 13d) and determine the position in

dependence on the desired work piece length.

Please note: The hexagon nut travels in the guide

of the limit stop! Fix the clamping piece with the

knurled screw 9.While sawing, the piece to be

sawn is pushed up to the limit stop and can be

crosscut as shown in fig. 12.

Sawing

Caution!

Your FET may not be used for slitting (notch com-

pleted in the work piece)! To groove or notch, please

by all means use the Proxxon groove-milling device

(article number 28736).

Hold the work piece on the saw table as shown in

fig. 14. Adapt the feed according to the material, the

saw blade and the work piece thickness! Hard mate-

rials, fine saw blades and thick work pieces do not

“tolerate” as much feed as soft materials, rough saw

blades and thin materials.

Always operate the saw from the position as shown

in Fig. 14a so that you are always in optimal control

of the work piece. Stand in front of the saw while

sawing! Never saw with your FET from the side or

even from the back. Ensure sufficient stability while

you work!

If you process correspondingly small work pieces

then use the included push-rod, as shown in fig. 15.

This prevents your hands from coming to close to the

revolving saw blade and thus reduces the risk of in-

jury:

Always keep the push-rod close to hand while work-

ing!

If the device is not in use, please use the supplied

push-rod in the designated housing fixture (fig. 14b)!

Please note:

• Only use perfect saw blades.

• Always remove the mains plug for maintenance

and upkeep work.

• Do not let the device operate unsupervised.

When sawing, press the work piece onto the work

plate, guide with sensitivity and with little force, more

pressure on the work plate, less pressure against the

saw blade. Guide the work piece slowly into the saw

blade, particularly if the blade is very thin and the

teeth very fine or if the work piece is very thick.

General tips on sawing

For good results, please note the following points:

• When sawing, press the work piece onto the work

plate, guide with sensitivity and with little force;

more pressure on the work plate, less pressure

against the saw blade.

• Make sure that the work piece is lying properly on

the saw table (no burrs or sawdust)

• Adapt the feed to the requirements by saw blade,

speed and work piece material.

• Guide the work piece slowly into the saw blade,

particularly if the blade is very thin and the teeth

very fine or if the work piece is very thick.

• Only use perfect saw blades.

• Do not let the device operate unsupervised.

• Carefully mark out the check line.

• Make sure there is good lighting.

• Always work with connected dust suction!

• If necessary, use the included push-rod to feed the

work piece.

Changing the saw blade

Your saw is equipped with a carbide-tipped saw

blade with 24 teeth and an 80 mm diameter ex

works.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FET Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info