Bedienungsanleitung Proxxon FET (Seite 18 von 24) (Englisch)

782211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

This is very well suited for most „sawing jobs“, guar-

antees clean cuts in the most various materials and

guarantees long service life. But it will not last for

ever, of course: Wear will occur depending on the in-

tensity of use: The saw blade will become dull, more

force to push the work piece is required and the

quality of the cut is reduced, the mechanics of the

machine are stressed more strongly than necessary.

Then it is high time to replace the saw blade with a

new one. It can also be necessary to use a different

saw blade type for a particular task (see also the

chapter „Choosing the right saw blade“ below) so

that it needs to be exchanged for the standard blade.

The work steps remain the same, naturally.

1. Disconnect the mains plug!

2. Turn the saw blade down as described in the

chapter „Height adjustment of the saw blade“.

3. Swing open the housing as described in section

„Swinging open the upper housing part“.

4. To release the screw 1 (fig 16a), the shaft on which

the saw blade 2 is mounted must be blocked. To

do so, insert the smaller of the two included Allen

keys 3 through the small drill hole 4 in the saw

table and from there insert it into the saw blade

shaft through a cross-hole, see fig. 16b. If neces-

sary, this drill hole must be „found“ somewhat by

turning the saw blade by hand. A hint: For this pro-

cedure we recommend you adjust the saw blade

to a relatively high height and then to lower it

somewhat after finding the latching drill hole with

inserted Allen key in order to gain full access to

screw 1.

5. Release the hexagon-head screw 1 with the larger

of the two Allen keys and remove together with

disc 5.

Caution!

The teeth of even worn saw blades are still very

sharp! Risk of injury!

6. Remove the old saw blade upwards and through

the saw blade opening and place the new saw

blade on the shaft. Make sure the saw blade drill

hole is seated correctly at the shaft shoulder!

7. Please also make sure that the teeth are pointing

in the direction as shown in the figures!

8. Screw on disc 5 with the hexagon-head screw 1

and tighten. Note that the saw shaft still needs to

remain blocked with the small Allen key.

9. Release the latch, push down the upper housing

part and lock with the knurled screw.

Choosing the right saw blade

Caution!

When choosing the saw blade, make sure at all costs

that the highest permissible speed is sufficiently high

enough for the idling speed of the saw!

Only use original Proxxon saw blades.

The choice of the suitable saw blade has an enor-

mous impact on the work result: Various characteris-

tics such as work piece material, saw job intensity

and the desired quality of the result must be consid-

ered. Proxxon has 4 different saw blades that can be

used to operate the machine:

Super-Cut

Ø 85 x 0.5 x 10 mm,

Suitable for more soft woods and plastics

Article number 28 731

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FET Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info