Bedienungsanleitung Proxxon FET (Seite 15 von 24) (Englisch)

782211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Dust suction

At the back of the housing of your FET you will find a

connecting piece for dust suction, see fig. 9: a vac-

uum cleaner is connected here.

This should always be operational while working! Not

only because it guarantees a clean working environ-

ment, but also because this prevents the interior of

the saw from becoming contaminated from sawdust.

The vacuum cleaner hose is simply connected to the

rubber adapter, as shown in the picture 9a.

Another small tip:

When using the Proxxon CW-matic vacuum cleaner,

manual switching on and off is no longer necessary.

The CW-matic is equipped with an automatic control

that switches on and off automatically whenever the

electrical tool is activated or deactivated.

Working with the limit stops

Working with the longitudinal stop

Longitudinal stops are indispensable working aids for

producing any number of work pieces with exactly

the same width (or length) without having to mark the

piece to be sawn each time. The material to be sawn

is simply guided along the longitudinal stop with

slight pressure during the sawing procedure. The

measure of the finished sawn work piece thus corre-

sponds to the distance of saw blade and limit stop

edge.

If necessary, you can refer to the scale at the front of

the housing to adjust the longitudinal stop.

The future measure of the work piece can be read off

from a marking. However, the scale must be adjusted

exactly to the saw blade beforehand – therefore „ze-

roised“. How this is done is described below.

The scale is dimensioned for the use of the limit stop

on both sides of the saw blade. The most various

sawing tasks are therefore no problem.

Inserting, or removing, the longitudinal

stop

The longitudinal stop 1 (fig. 10a) is inserted, or re-

moved, from the side (from the right or left) in the

guide 2 at the saw table. While you are shifting, in-

serting, or removing the longitudinal stop make sure

that both fixing options locking handle 3 and knurled

screw 4 are released! The scale 5 was attached with

restricted rotation. Please make sure it is properly

seated when you insert the limit stop.

Rough adjustment of the longitudinal

stop

The rough adjustment simply by shifting the longitu-

dinal stop without using the scale 5 (fig. 10b) is suffi-

cient for many cases.

When you shift the longitudinal stop, please make

sure that both fixing options locking handle 3 and

knurled screw 4 are released!

Once the desired position is achieved, the longitudi-

nal stop is arrested by tightening the knurled screw 4

and then clamped with the locking handle 3.

Adjusting the longitudinal stop with the

help of the scale

1. When you shift the limit stop, please make sure

that the locking handle 3 and knurled screw 4 are

released.

2. The longitudinal stop can now be shifted in its

guide using the help of the scale 5. The position

can be read from the left front limit stop edge 6,

see fig. 10 c. Caution: The read value will only

agree if the „zero position“ of scale 5 is correct!

How to correctly adjust the zero position of the

scale is described in the section „Adjusting the

limit stop scale“.

3. Arrest the longitudinal stop by tightening knurled

screw 4 and then clamping the locking handle 3.

Adjusting the limit stop scale

(zero position)

For the reliable use of the scale 5 for the longitudinal

stop, its position must first be co-ordinated to the

saw blade – therefore „zeroised“. This process is ab-

solutely necessary after the saw blade has been re-

placed with a saw blade of different thickness, or if

the limit stop was finely adjusted (see section „Fine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FET Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info