Bedienungsanleitung Proxxon TG 125-E (Seite 14 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

782214

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Please note in general:

Proxxon bits and cutters have been designed to work

with our machines, which makes them optimal for

their use.

We will not assume any liability whatsoever for the

safe and proper function of our devices when using

third-party bits and cutters!

5.4 Adjusting the grinding table angle

(fig. 5):

Caution:

Before adjusting the grinding table, always discon-

nect the mains plug to prevent the disc being started

up accidentally. Risk of injury!

1. Loosen rotary knob 1 At the same hold rotary

knob 2

2. Swing grinding table 3 into the desired angle posi-

tion and check the set value on angle scale 4.

3. Tighten rotary knob 1. At the same hold rotary

knob 2

5.5 Connecting the dust exhaust (fig. 6):

Caution:

Before connecting the dust exhaust, always discon-

nect the mains plug to prevent the disc being started

up accidentally. Risk of injury!

It is recommended to always work with the dust

exhaust! This not only guarantees clean working, it

also reduces the hazardous effect of some dusts!

1. Push adapter piece 1 onto connecting piece 2 of

the machine

2. Push rubber adapter 3 onto adapter piece 1

3. Insert vacuum cleaner nozzle 4 into rubber

adapter 3

4. Switch on vacuum cleaner when working

Another small tip:

When using the Proxxon CW-matic vacuum cleaner,

manual switching on and off is no longer necessary.

The CW-matic is fitted with an automatic control

device; it automatically switches on and off when the

power tool is switched on and off. The same effect

can be obtained with traditional vacuum cleaners by

using our vacuum control device.

6 Working with the TG 125/E disc grinding

machine

Caution:

Please note that the grinding disc turns to the left! If

you use the left side when working with the attached

grinding table, the work piece can be guided easily

and securely, thus effectively preventing it from being

hurled away!

Caution:

When grinding metallic work pieces, such as when

grinding knife blades for example, or when grinding

stone or ceramics the material to be ground can

become very hot! Do not hold the material to be

ground near the grinding surface in order to avoid

burns!

Caution:

Wear suitable gloves to avoid abrasions especially

when working with coarse sandpaper and when pro-

cessing smaller work pieces!

1. If mitres are to be ground, adjust the grinding

angle as described above

2. Insert the mains plug

3. Switch on the machine at On-Off-Switch

4. Set the required speed on the speed control but-

ton (pos. 3, fig. 1)

Please adjust the size of the work piece to the size of

the machine! A work piece that is too large and too

heavy can overburden the drive or the construction of

the machine and cause damage or injuries!

6.1 Working with the angle stop (fig. 7):

If, for example, the ends of somewhat thinner strips

are ground for mitre, it is advantageous to use the

angle stop included in the scope of delivery.

1. Loosen knurled screw 1

2. Set the desired angle on scale 2

3. Turn the knurled screw tightly and insert into the

intended table groove

4. Guide the desired workpiece up to the stop

against the grinding wheel as shown in the illus-

tration

- 14 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon TG 125-E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info