Bedienungsanleitung Proxxon TG 125-E (Seite 13 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

782214

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

- 13 -

5 Before work

5.1 Setting up your disc grinding machine

(fig. 2):

Note:

When setting up the machine, make sure that the

ground below it is level and secure! A secure stand is

indispensable for working with the machine!

Note:

When setting up and fixing the machine, always dis-

connect the mains plug to prevent the disc being

started up accidentally. Risk of injury!

Caution:

During all adjusting and assembly work, such as

when adjusting the angle stop or when attaching or

removing the grinding table, disconnect the mains

plug to prevent the device from starting up uninten-

tionally!

The disc grinding machine can be operated in two

different positions: Once in the normal horizontal

position or standing vertically (for sharpening tools

and blades for example).

In both positions, the machine should be securely

clamped with the enclosed vice, as shown in fig. 2.

5.2 Removing and inserting the grinding

table (fig.3):

Caution:

Before removing and inserting the grinding table,

always disconnect the mains plug to prevent the disc

being started up accidentally. Risk of injury!

Normally, your TG 125/E is operated with the

attached grinding table (as in delivery condition).

Additionally, there is also the possibility, where

required, of removing the grinding table, if this is nec-

essary for certain tasks or for changing the grinding

wheels.

Caution:

Please note that when working particularly in the

operating mode without the grinding table, always

make sure to control the work piece by holding it

firmly and securely in order to prevent it from being

flung about.

Use the machine in the horizontal position with

attached grinding table, if possible!

1. Remove Allen head screw 1

2. Remove the grinding table with grinding table

holder 2 by pulling out from the front

3. To insert, simply push into the normal position

4. Turn in Allen head screw 1 again

Caution:

If the grinding disc is blocked due to a work piece

that is jammed between the grinding disc and the

grinding table, immediately shut off the device using

the On/Off switch and disconnect the mains plug.

Only put the device back into operation after the

jammed work piece has been removed!

5.3 Affixing and replacing grinding wheels

(fig. 4):

Note:

Before affixing or replacing the grinding wheels,

always disconnect the mains plug to prevent the disc

being started up accidentally. Risk of injury!

Two grinding wheels in each of the grain sizes 80,

150 and 240 are supplied as initial equipment with

your disc grinding machine; these can also be easily

obtained as spare parts. It is therefore no problem to

change wheels, whether because of wear or because

discs with various grain sizes are required when

working.

Caution:

When replacing the wheels, it is advisable to remove

the grinding table as described in the previous sec-

tion!

1. Remove the rear protective foil above the adhe-

sive surface from the desired wheel,

2. Push the wheel evenly and bubble-free onto the

grinding disc.

3. To replace, simply remove the grinding wheel

again and push on the new wheel.

Accessories

For more detailed information on accessories, please

request our device catalogue from the address speci-

fied on the last page in the warranty information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon TG 125-E Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info