Bedienungsanleitung Rebox RE-2250MG (Seite 41 von 47) (Holländisch)

7894

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

www.rebox.tv

a quick scan and will find all channels that have been listed by Canal Digitaal. The found

channels will be stored in your receiver in a logical order. “Free only” (Free to Air) only or

“All Channels” to find all available channels on the satellite.

• Scan channels from the satellite: Your receiver allows you to use 4 types of channel

scans:

• AutoScan (Red Button): Starts the automatic channel scan by using the parameters that

you have set in the “Channel Set-up menu”. Please also refer to page 18, “5.1.1

Channel Organiser Menu”.

• Net. Scan (Green Button): “Network Search” Performs network search for a

transponder.

• Transponder Scan (Yellow Button): Search channels from current specific transponder.

• PID (Blue Button): You can search a specific channel by entering the PID value of a

channel. If you press the Blue (PID) button, the PID screen is displayed. Enter the PID

value and press the Blue button again. To cancel the PID value, press BACK on the

remote control or press the Blue (PID) button to search the channel. You should enter

V-PID, A-PID and P-PID as described in “Editing channels from the channel list”

(Described in section 5.1.1)

Tip:

Check the level and quality of the signal bar before searching any channels. The signal level of the TP

of the current satellite is displayed. The green bar is displayed if the settings are correct, otherwise the red bar is

displayed and you cannot get the channel. In the latter case, check if your dish is aimed at the selected satellite or

if the DiSEqC switch of the LNB overlaps with another satellite. Also, change the Frequency with the Left/Right

button until the Green bar is displayed to get the valid transponder. If you press the Red (Auto Scan), Green (Net.

Scan), Yellow (TP Scan), or Blue (PID) button the channel searching status is displayed (Figure 24)

5.1.4.3.1 Positioner Set-up (if you are using a Motorised positioner with DiSEqC1.2)

If you are using a motorised positioner with DiSEqC 1.2 you will have to set the positions of the satellites you want

to scan. This function is available only if in the “LNB Set-up” menu and the LNB Dish field is set to “Moved”. (As

described in “LNB Set-up” (Described in section 5.1.4.2).

Before you start:

1. Make sure that your installer has set the centre position of your dish.

2. Make sure that the mechanical limits of your motor are set, so that no damage can be done to

your dish by moving it too far to the East/West.

3. Make sure you set the highest Symbol Rate (Ksymbols/sec) for your chosen transponder (TP).

The Signal level and Quality indicator will help you set up the best dish position possible.

4. Use your UP/DOWN buttons to select the “Dish Position" field in the “Channel Set-up” menu.

( Note that the LNB dish in the LNB setup menu is set to “Motorized”.)

5. Press the OK button and the “Positioner Set-up” Menu will be displayed.

6. Start setting the position of the selected satellite.

7. Use your UP/DOWN buttons to go to field “Centre” and use your Left/Right buttons to put the

centre field to “On”.

8. Press OK, and your dish will move to the centre position. It takes your dish maximum 30 seconds

to move to its central position.

9. To know in which direction you will need to move your dish, you will need to know the position of

the satellite you want it to position to.

10. If correctly installed, your installer has set the centre position of your dish to the “true” South if in

the Northern hemisphere and to “true” North if in the Southern Hemisphere.

11. If for instance you want to set the position for Astra 19.2°East, you know that you will have to

move your dish to the left using the Left button. If you want to set the position for instance to

Eutelsat 12.5°West, you know that you will have to move your dish to the right using the Right

button. (As viewed from the rear of the dish)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rebox RE-2250MG Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info