Bedienungsanleitung Robbe Futaba FF-10 (Seite 8 von 119) (Englisch)

520097

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

MODULE: TP-FM/TM-10 2.4G

• Module may be easily removed and a module on a different channel (or even band) reinserted to change the frequency on

which the 10C transmits.

• TP-FM module transmits both FM (

PPM

) and

PCM

. No need for a second module. TM-10 2.4GHz module transmits both

2.4G-7ch

and

2.4G-10ch

• All transmission circuitry is included in the module, so no retuning is needed when changing channels or even bands.

• Frequency band is changed by inserting a module on the proper band, including for international or ground model use.

• TP-72 FM module: In North America it is against FCC regulation to change the crystal within the transmitter module

to a different channel. All such transmitter crystal changes must be performed by a certiﬁ ed radio technician. Failure to

properly tune a system to its new channel may result in decreased range and may also result in interference to other types

of frequency users on adjoining channels. Doing so also voids your AMA insurance.

Non-Futaba brand modules are not FCC certiﬁ ed for use with this radio and therefore are against FCC regulation to use.

Doing so also voids your AMA insurance.

• The FSS synthesized module for the 9Z family of radios is NOT compatible with the 10C.

• Radio system beeps and RF LIGHT goes out to indicate module is not installed and radio is not transmitting.

• TP-75 FM modules may also be used with the 10C for ground use modules such as robotics, rocketry, trains, cars, and

boats.

RECEIVER: R138/R148/R1410/R6014FS

• The R138 or R148 FM 8-channel or the R138 PCM 8-channel or R1410 PCM 10-channel receiver included with your

system is a high-sensitivity narrow-band dual-conversion receiver. The R6014FS 2.4GHz 14-channel is FASST-2.4GHz

Multi-ch mode receiver.

• Note that your 10C transmitter with TP-FM module or TM-10 2.4G module is capable of transmission on both

PPM

(FM)

and

PCM

or on both

2.4G-7ch

and

2.4G-10ch

with just a simple programming change and just turning the transmitter off

and back on. (See p. 35.)

• Any Futaba narrow band FM receiver (all produced after 1991) on the correct frequency band and frequency may be used

with the 10C.

• Any Futaba PCM 1024 receiver on the right frequency band and frequency may be used with the 10C (all 1024 receivers

say PCM1024; receivers which say PCM but not 1024 are 512/2048 resolution and not compatible).

• Futaba FASST-2.4G R6014FS or R608FS receiver may be used with the 10C at

2.4G-10ch

mode. Futaba FASST-2.4G

R607FS or R617FS receiver may be used with the 10C at

2.4G-7ch

mode.

Transmitter

Receiver

R606FS

R616FFM, R607FS,

R617FS

R608FS, R6014FS

TM-14 Module

Multi-ch mode

——Okay

7ch mode Okay Okay —

TM-10 Module

10ch mode — — Okay

7ch mode — Okay —

TM-8 Module

8ch mode — — Okay

7ch mode — Okay —

TM-7 Module — Okay —

T7C 2.4G System Okay Okay —

FASST transmitter module, system

and receiver compatibility

• 72MHz band: NEVER attempt to change a receiver’s band by simply changing crystal (i.e. removing a 72MHz crystal

and inserting a 75MHz crystal). A receiver that has a crystal installed from a different frequency band without retuning

will not receive properly and will have dramatically decreased range.

In North America the receiver included with this system may have its frequency changed by simply changing the crystal

as long as it remains in the same half the band. A low band receiver between channels 11 and 35 may be changed to any

other channel between 11 and 35 without requiring any tuning. A high band receiver between channels 36 and 60 may

similarly be changed. Receivers being changed from a high band channel to a low band or vice versa require proper

tuning and service by the Futaba Service Center.

SERVOS

• Please see technical speciﬁ cations page for speciﬁ cs on the servos included with your system.

•The included receiver is compatible with all J-plug Futaba servos, including retract, winch, and digital servos.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FF-10 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FF-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info