Bedienungsanleitung Robbe Futaba FX-40 (Seite 27 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Curve set-up

FX-40

• SETTING CONTROL CURVES / MIXER CURVES

The method of setting transmitter control travels and curves has also

been standardised in the inter

ests of ease of operation. The transmitter

offers pre-programmed and freely variable curves for the programm-

able mixers and mixer functions as well as all twelve control functions.

The software initially suggests 2, 3, 5, 7 or 9 points according to the

Select menu, but the user is free to vary the actual number of points

within the range 2 to 17 when dealing with the free curves (line and

curve).

The method of setting up and adjusting these curves is the

same for all the Set-up menus, and the pr

ocess occurs very

equently. For this reason it would be a waste of space to

repeat the description every time, so the following section is

presented only once, and can be applied to all the other

This section deals with the method of setting the characteristics of a

transmitter control, using the transmitter control travel (AFR) menu as

an example.

When you select the AFR menu the software suggests the default line-

ar 3-point curve. If you press the “Linear” button field, another window

appears in which you can select the following curves:

Linear = 3-point straight line

EXP 1

= Exponential curve, symmetrical ar

ound the centre

EXP 2 = Exponential curve, between the end-points

VTR = Variable 5-point curve

Line = Variable 9-point (17-point) curve

Spline = Variable 9-point (17-point) curve with rounding

LINEAR = 3-POINT STRAIGHT LINE, ASYMMETRICAL

If you select this setting the ratio of transmitter control travel to servo travel

is 100% to 100%, i.e. linear, and the characteristic curve is a straight line.

The characteristic curve can be varied separately for each side of neutral by

adjusting Rate A (left-hand half of contr

ol travel) and Rate B (right-hand half

of control travel). Pressing the “Rate A” button field activates the control but-

ton fields; you can now set the desired rate using the vertical button field.

Note that the double-arrow button ( ) means a large increment, the single-

arrow button () a small increment. You can also adjust the setting using the

3-D Hotkey (= 0.5% per click).

SEPARATE.

Press the “Separate.” button field, and answer the subsequent question

“Combine?” with “Yes”. The display changes to “ Separate.”.

ou can now adjust the setting equally for both sides, i.e. symmetrically.

OFFSET

The Offset setting changes the neutral position of the transmitter control

relative to the servo centr

e point. If the offset value is up to 50%, the travel

remains the same for both sides of neutral, but if the value is any higher, the

servo travel will be at its end-point at one extreme, so the travel becomes

increasingly asymmetrical.

X-OFFSET

The X-Offset setting changes the centre position of the servo relative to the

neutral position of the transmitter control. The total travel is unchanged, alt-

hough contr

ol travel becomes increasingly asymmetrical with increasing X-

Offset values. In the extreme case one side is 99%, the other side 1%.

RESET BUTTON

Resets the particular value to the factory default setting.

Transmitter control travel

+ 5%

+ 0,5%

- 0,5%

- 5%

Current position of transmitter Control

Servo travel

Transmitter control characteristic / servo travel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info