Bedienungsanleitung Robbe Futaba FX-40 (Seite 43 von 105) (Englisch)

520094

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Linkage Menu

FX-40

16.7 FUNCTION

The transmitter employs a new, graphical method of selecting

the model type as basis for the mixer functions and transmitter

contr

ol arrangement (stick mode), and this automatically gene-

rates the optimum configuration for the selected model type.

We r

ecommend that you keep to this set-up if possible, so that

you are always using a standard configuration.

The “Function” menu clearly shows the output to which the

corresponding servo is connected, and which transmitter con-

trol is used to operate it. Where a single function operates two

or more servos, the corresponding transmitter controls are

configured accordingly. Within an individual model type the

configuration varies little, although the number of channels in

use may increase if the number of wing flaps and other control

surfaces is higher than usual.

The situation is different when you switch from one model type

to another. For example, if the model type changes from a nor-

mal tail to a tail layout with two elevator servos (Ailvator), the

sequence of functions is necessarily different. The same also

applies to model gliders (powered and unpowered), and for

flying wing models with and without winglets.

NEW FUNCTION SEQUENCE

For the PCM-G3 system the second aileron output has been

shifted to output 5, in order to maintain compatibility with

small five-channel and six-channel r

eceivers. The higher num-

ber of channels has also necessitated this change. This means

that the receiver channel sequence is not the same as that of

the PCM 1024 / PPM 8 system.

However, you can select any function sequence you like in this

menu, in order to maintain compatibility with the PCM 1024

and PPM 8 system.

NOTE:

If you need to change the function sequence when using the

PCM-G3 system, please ensur

e that associated functions ar

assigned together within the channel groups 1 … 6 or 7 … 12.

Do not assign paired functions to channels 6 and 7, as this

could result in different servo transit times.

SERVO ASSIGNMENT TABLES

These tables are printed in Section 6 - Servo

connections - on page 16.

Free choice of function sequence

The “CH” (channel) numbering corresponds to the

output number at the receiver

• Press the Function button, and define the desired

function for this channel.

Free choice of transmitter control

Each control function can be assigned to any trans-

mitter control.

•

Press the transmitter control, and define the control

for this function.

Multiprop channels

It is also possible to expand two of these outputs using optional

Multi-Decoders (No. F 1400). These modules are connected to

the receiver

, and provide eight channels each for auxiliary wor-

king systems on multi-function models.

Sepa / Glob - Separate / Global

Use the Glob / Sepa button to determine whether the transmit-

ter control is to be the same for this function in all flight modes

(= Glob). If the function is changed to Sepa (separate), you can

use a dif

ferent transmitter control for this function in each flight

mode. In this case the display will change when you operate the

selected flight mode change-over switch. It is also possible to

set up a combination of global and separate-acting transmitter

controls.

Separate / Global: indicates whether the trim

is to affect all flight modes globally, or varies

according to the flight mode selected.

Display of the active flight mode

For setting

the virtual

functions

(see page

44).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robbe Futaba FX-40 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robbe Futaba FX-40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info