Bedienungsanleitung Robomow MS2500 (Seite 48 von 62) (Englisch)

644646

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Robomow S models

Chapter 7 Troubleshooting

7.1 Text error-messages

Robomow continuously monitors its operation. It produces text messages to assist you in smoothly running it: text

messages in case of an operational fault as well as text messages that prompt the user to perform a certain action.

P Usually, if the mower stops, a message is displayed. This display stays on for 15 minutes.

) If you arrive later than those 15 minutes, the display will be blank.

P To wake Robomow up and see the last text message displayed prior to stopping, press

The following table displays all fault message displays and their most common causes. The next table will give details

and possible causes of other faults, that do not provide fault messages.

If a fault cannot be dealt with using these tables, please call your service provider.

7.2 Error Messages And Corrective Actions

The list is alphabetical, by message text

Message

Displayed

Probable Cause/Event Corrective/User Action

Base Problem

- Robomow fails to enter the Base Station

several times continuously.

- Adjust the Base Station position.

- Clean the contacts with a brush or piece of cloth.

Bumper Pressed

- Bumper is constantly being pressed.

- Move mower away from object that presses against the

bumper.

Check Inactive

Time

- Too many Inactive Days and/or Hours have

been set for your lawn area. Current settings

will not be changed.

- Mowing Frequency is too high for current

settings of Inactive Time. The Inactive Time

settings will be set to defaults.

- Area setting is too high for current settings of

Inactive Time. The Inactive Time settings will

be set to defaults.

- Decrease the number of Inactive Days and/or the

number of Inactive Hours to allow Robomow to complete

mowing your lawn.

- Decrease Mowing Frequency (see Section 4.3.2.2)

- Decrease Area setting

Check Mow

Height

- Mowing motor has faced an over-current for

too long as a result of high grass or an obstacle

that is stuck or wrapped around the blade.

- Something is preventing a blade from rotating

freely. Severe grass accumulation under the

mowing deck; rope or similar object wrapped

around mowing blade.

- CAUTION – Switch off the Safety Switch before

checking the blades.

- Inspect blades for foreign material or debris preventing

rotation.

- Clean out accumulated grass clippings using a wooden

stick.

Check Power

- Power Box is not plugged properly into the

main Power Box.

- Confirm Power Box is plugged into the main power plug

socket.

- No power to plug socket or main power is shut

off.

- Turn power on to the main plug socket.

- Check the mains supply using another appliance.

- The mower or Charging Station contacts are

dirty.

- Clean the contacts with a brush or piece of cloth.

- Charging is not detected, although there is

physical contact between the mower and the

Base Station contacts.

- Confirm a good connection of the Power Box to the

Base Station.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow MS2500 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow MS2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info