Bedienungsanleitung Robomow MS2500 (Seite 49 von 62) (Englisch)

644646

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Troubleshooting

Message

Displayed

Probable Cause/Event Corrective/User Action

Cross Outside

- The Perimeter Wire is too close to the edge.

- The lawn slope is too big.

- Robomow does not succeed to turn in place at

the edge and it causes the mower to slip out of

the area.

- Robomow has slipped out of the Perimeter

Wire loop because of a sloping area or wet

grass.

- Move the wire towards the inner side of the lawn.

- Do not include area with very steep slopes.

- Fill holes and pits in the ground.

- Increase the cutting height.

Drive Overheat

Cooling…

- The drive motors have been working under a

severe load for too long.

- No need to do anything.

- Robomow will renew the operation automatically as

soon as the drive motor will cool down.

Front Wheel

Problem

- The Front Wheel has left the ground for too

long time during operation.

- If Robomow has driven onto an obstacle, raising the

front end:

Remove or exclude the object from the mowing area.

- If Robomow is being used on a slope too steep for safe

mowing:

Exclude this from the mowing area.

- If High grass is preventing the front wheel from fully

riding on the ground:

Raise the cutting height.

- If the ground contains large holes or indentations where

the front wheel can drop into when passing across:

Fill these areas with dirt and level off.

Handle Lifted

- The handle is lifted while trying to start the

operation

- Push the carrying handle down back to its position to

enable automatic operation.

Key Pressed

- One of the operating panel buttons is

constantly pressed.

- Press

to confirm the message and to continue

operation. This message is displayed to inform only.

Keys Locked

- Child Lock feature has been activated.

- Press the

button and then press the

button.

Child Lock can be deactivated under the Settings

menu.

Mow Overheat

cooling…

- The mowing motor has been working under a

severe load for too long of a time.

- No need for action – Robomow will renew automatically

the operation, as the mowing motor will cool down.

No wire signal

- Power Box / Perimeter Switch is not turned on

or not connected to the zone intended to mow.

- Power Box may need to be restarted

- The Perimeter Wire is not connected to the

Base Station / Perimeter Switch.

- The Perimeter Wire is cut.

- Make sure the Base Station is connected to the mains

supply.

- Disconnect the Power Box from the mains power and

reconnect after 10 seconds.

- Check the Perimeter Switch is connected to the correct

zone and is turned on.

- Check the connection of the Perimeter Wire to the Base

Station / Perimeter Switch.

- Check for cut in the Perimeter Wire.

Rain detected

- The operation is delayed as Robomow detects

rain.

- Robomow should resume operation 30 minutes

after it stops to detect the rain.

- No need for action

- The message is displayed as long as rain/humid

conditions are detected by Robomow. Mowing will

restart automatically.

Raise Mowing

Height

- TurboMow mode has been activated.

- It is recommended to raise mowing height before

starting the mower in TurboMow mode. Refer to sections

3.1 and 4.3.7 in the User Manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Robomow MS2500 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Robomow MS2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info