Bedienungsanleitung Roland BK-5 (Seite 77 von 160) (Englisch)

708951

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Mastering Tools

Backing Keyboard BK-5

Mastering Tools

The BK-5 contains an effects processor that applies to

all real-time, rhythm and SMF song parts.

This processor is called “Mastering Tools”, because it

allows you to perfect the signal mix to adapt it to the

sound system you are using.

The parameters discussed here can be selected using

[MENU] button ‰ “Mastering Tools”.

Compressor

This multi-band compressor/limiter allows you to pro-

cess three frequency ranges separately. A compressor

reduces high levels (peaks) and boosts low levels,

smoothing out fluctuations in volume.

To edit the Compressor parameters, use [MENU] button

‰ “Mastering Tools” ‰ “Compressor”.

Select a keyboard part, an SMF song or a

rhythm and start playback.

Set the “Switch” parameter to “On” to acti-

vate the compressor.

The compressor is now active. (Select “Off” to switch

the compressor back off.)

Use the [CURSOR÷VALUE] dial to select the

“Preset” parameter, then press the [ENTER/

SELECT] button.

Rotate the [CURSOR÷VALUE] dial to select

one of the available presets.

The available presets are:

If none of the preset memories contains the

settings you need, press the [ENTER/SELECT]

button to select and set the following

parameters:

1. Hard Comp

2. Soft Comp

3. Low Boost

4. Mid Boost

5. High Boost

6. Standard

7. User

Parameter Setting Explanation

Level 0~127 Use this parameter to set

the compressor’s input level.

The higher the value, the

stronger the three frequency

bands are compressed.

The value you set here is

added to the “Level” settings

of the three bands. Do not

set this parameter to “0” if

the compressor is switched

on, because doing so means

that the keyboard parts, the

SMF song or Rhythm parts

are no longer audible.

Gain –12~0~

12dB

Use this parameter to cor-

rect the level at the com-

pressor’s outputs. If the

settings of the remaining

parameters lead to a signifi-

cantly lower level, select a

positive value. If your set-

tings lead to a significantly

higher level, select a nega-

tive value. “0” means that

the level is neither boosted

nor attenuated.

High/Mid/Low: Because “Attack”, “Release”, “Threshold”,

“Ratio” and “Level” are the same for each band, we will

only discuss them once. As you see, each of the three fre-

quency ranges has its own set of parameters that allow

you to specify their behavior.

Attack 0~100ms Use this parameter to spec-

ify how fast the compressor

of the band in question

should start processing the

signal once the level of that

band exceeds the “Thresh-

old” level. Choose a smaller

value if you prefer a com-

pression similar to that of

FM radio stations. Higher

values may yield a “snap-

pier” or “funkier” sound.

Release 50~

5000ms

This parameter allows you to

specify how fast the com-

pressor of the corresponding

band should stop working

when the signal level drops

below the “Threshold” value.

BK-5_US.book Page 77 Thursday, May 23, 2013 7:01 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland BK-5 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland BK-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info