Bedienungsanleitung Roland BK-5 (Seite 79 von 160) (Englisch)

708951

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Mastering Tools

Backing Keyboard BK-5

If none of the preset memories contains the

settings you need, you can change the fol-

lowing parameters by first pressing the

[ENTER/SELECT] button and then using the

[CURSOR÷VALUE] dial.

Write User

This function allows you to save the settings you

made on the “Equalizer” page.

Press the [WRITE] button.

Rotate the [CURSOR÷VALUE] dial to select

“YES”, then press the [ENTER/SELECT] but-

ton to save the current settings.

The display shows a confirmation message.

If you don’t want to define the current settings as

the default state, rotate the [CURSOR÷VALUE] dial to

select “NO”, then press the [ENTER/SELECT] button.

The BK-5 then returns to the “Equalizer” page.

NOTE

There is only one “User” memory for your own settings. By

saving new settings, you therefore overwrite the previous

ones.

NOTE

When you switch on the BK-5, it automatically loads the

“User” settings.

Parameter Setting range Explanation

Level 0~127 Use this parameter to set

the equalizer’s input

level. This may be neces-

sary when the level of

the input signals is so

high that the sound dis-

torts.

NOTE

Do not set this param-

eter to “0” if the equal-

izer is switched on,

because doing so

means that the key-

board parts, SMF song/

rhythm is/are no

longer audible.

Gain –9~0~9dB Use this parameter to

correct the level at the

equalizer’s outputs. If

the settings of the

remaining parameters

lead to a significantly

lower level, select a posi-

tive value. If your set-

tings lead to a

significantly higher level,

select a negative value.

“0” means that the level

is neither boosted nor

attenuated.

High

Frequency

2000~

12000Hz

Allows you to set the

cutoff frequency of the

high band (this is a

shelving filter).

High Gain –15~15dB Use this parameter to set

the level of the selected

“High” frequency. Posi-

tive values boost

(increase the volume of)

that frequency band,

negative values cut

(attenuate) it.

Mid Fre-

quency

200~8000Hz Allows you to set the

cutoff frequency of the

middle band (this is a

peaking filter).

Mid Q 0.5, 1, 2, 4, 8 Use this parameter to

specify the width of the

“Mid Frequency” band

that you want to boost

or cut. Smaller values

mean that neighboring

frequencies above/below

that value are also

affected.

Mid Gain –15~15dB Use this parameter to set

the level of the selected

“Mid” frequency.

Low Fre-

quency

50, 80, 100,

150, 200, 250,

300, 400Hz

Allows you to set the

cutoff frequency of the

low band (this is a shelv-

ing filter).

Low Gain –15~15dB Use this parameter to set

the level of the selected

“Low” frequency.

Parameter Setting range Explanation

BK-5_US.book Page 79 Thursday, May 23, 2013 7:01 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Roland BK-5 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Roland BK-5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info