Bedienungsanleitung Rotel RSX-1056 (Seite 18 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

RSX-1056 Surround Sound Receiver

NOTE

: When using digital connections, you

should also make the analog audio input con-

nections described previously. The analog

connection is necessary to record to an ana-

log recorder in some circumstances or for

ZONE 2 operation

Digital Outputs

The RSX-1056 has two digital outputs (one

coaxial and one optical) to send the digital

signal from any of the digital inputs to a digi-

tal recorder or outboard digital processor.

When a digital input source signal is selected

for listening, that signal is automatically sent

to both digital outputs for recording.

NOTE

: Only digital signals from source com-

ponents are available at these outputs. Ana-

log signals cannot be converted and are not

available at the digital outputs.

Other Connections

AC Input

Your RSX-1056 is configured at the factory for

the proper AC line voltage in the country where

you purchased it (USA: 115 volts/60Hz AC

or CE: 230 volts /50 Hz AC ). The AC line

configuration is noted on a decal on the back

of your unit.

Plug the supplied cord into the AC INPUT

receptacle on the back of the unit.

NOTE

: Memorized settings and video labels

are preserved indefinitely, even if the

RSX-1056 is disconnected from AC power.

Master Power Switch

The large rocker switch on the rear panel is a

master power switch. When it is in the OFF

position, power to the unit is completely off.

When it is in the ON position, the front panel

STANDBY and remote control ON/OFF but-

tons can be used to activate the unit or put it

into standby mode.

NOTE

: After all connections are completed,

the rear panel master power switch should

be put in the ON position and usually left in

that position.

12V TRIGGER Connections

Many Rotel amplifiers offer the option of turning

them on and off using a 12 volt trigger. These

three connections provide this 12 volt trigger

signal from the RSX-1056. When the RSX-1056

is activated, a 12 volt DC signal is sent to the

amplifiers to turn them on. When the RSX-1056

is put in STANDBY mode, the trigger signal

is interrupted and the amplifiers turn off.

To use the remote turn on feature, connect one

of the RSX-1056’s 12V TRIG OUT jacks to the

12 volt trigger input of a Rotel amplifier, us-

ing a cable with mono 3.5 mm mini-plugs on

both ends. The +12 V DC signal appears at

the “tip” connector.

NOTE

: The 12V Trigger outputs can be config-

ured to turn on only when specific input

sources are activated. See the Input Setup

and Zone 2 Setup menus in the Setup section

of this manual for details.

REM IN Jacks

Two 3.5 mm mini-jacks (labeled ZONE and

EXT) receive command codes from an indus-

try-standard infrared receivers (Xantech, etc.),

used when the IR signals from a hand held

remote control cannot reach the front panel

IR sensor.

EXT: The EXT jack is used with an outboard

IR receiver to duplicate the front panel IR sen-

sor. This feature is useful when the unit is in-

stalled in a cabinet and the front panel sen-

sor is blocked or when IR signals need to be

relayed to other components.

ZONE: The ZONE jack is used with IR repeater

systems to receiver signals from IR control sys-

tems in remote location. For example, remote

control signals sent to the ZONE REM IN control

the ZONE 2 features of the RSX-1056 and can

be relayed to other components.

Consult your authorized Rotel dealer for in-

formation on external receivers and the proper

wiring of a 3.5 mm mini-plugs to fit the REM

IN jacks.

NOTE

: The IR signals from the EXT REMOTE

IN and ZONE REMOTE IN jacks can be re-

layed to source components using external

IR emitters or hard-wired connections from

the IR OUT jacks. See the following section

for additional information.

IR OUT Jacks

The IR OUT 1 & 2 jacks send IR signals re-

ceived at the ZONE REM IN or the EXT REM

IN jacks to an infrared blaster or emitter placed

in front of a source component’s IR sensor. In

addition, the IR OUT can be hard-wired to Rotel

CD players, DVD players, or tuners with a com-

patible connector.

These outputs are used to allow IR signals from

Zone 2 to be sent to the source components,

or to pass along IR signals from a remote in

the main room when the sensors on the source

components are blocked by installation in a

cabinet.

See your authorized Rotel dealer for information

on IR emitters and repeater systems.

Computer I/O

The RSX-1056 can be operated from a com-

puter with audio system control software from

third-party developers. This control is accom-

plished by sending operating codes from the

computer via a hard-wired RS-232 serial con-

nection. In addition, the RSX-1056 can be up-

dated using special software from Rotel.

The COMPUTER I/O input provides the nec-

essary network connections on the rear panel.

It accepts standard RJ-45 8-pin modular plugs,

such as those commonly used in 10-BaseT UTP

Ethernet cabling.

For additional information on the connections,

cabling, software, and operating codes for com-

puter control or updating of the RSX-1056, con-

tact your authorized Rotel dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RSX-1056 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info