Bedienungsanleitung Rotel RSX-1056 (Seite 20 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

RSX-1056 Surround Sound Receiver

The MULTI inputs are analog bypass inputs,

passing signals directly through to the Volume

Control and preamp outputs, bypassing all of

the digital processing. The RSX-1056 provides

an optional bass redirect feature that dupli-

cates the seven main channels and passes them

through an analog 100 Hz low pass filter,

creating a summed mono subwoofer output

derived from the main channels. See the

IN-

PUT SETUP

menu in the

Setup

section of this

manual for details on bass redirect feature.

TV Monitor

See Figure 4

Connect the TV MONITOR

output

to the cor-

responding

input

on your television monitor,

using composite video, S-Video, and/or Com-

ponent Video cables.

NOTE

: The RCA composite video output only

sends signals from RCA composite video

source inputs to the TV monitor. The S-Video

output only sends signals from S-Video source

inputs to the TV. The RSX-1056 upconverts

composite and S-Video signals to Component

Video signals.

When configuring the unit, you must specify

either an NTSC or a PAL standard TV moni-

tor. See the

Other Options

menu in the

Setup

section of this manual.

Speakers

See Figure 3

The RSX-1056 has built-in amplifiers to power

up to five speakers. There are five pairs of bind-

ing post connections (one pair for each speaker)

which accept bare wire, spade lugs, or ba-

nana plug connectors (in some markets).

NOTE

: Speakers should have an impedance

of 8 ohms or higher.

Each pair of connectors is color-coded for

polarity: red for positive and black for nega-

tive. All speakers and all speaker wire is also

marked for polarity. For proper performance,

you must maintain this polarity at all speaker

connections. Always connect the positive ter-

minal of each speaker to the corresponding

red speaker terminal on the RSX-1056 and the

negative speaker terminal to the correspond-

ing black connector on the RSX-1056.

There are connectors for FRONT LEFT, FRONT

RIGHT, SURROUND LEFT, SURROUND RIGHT,

and CENTER. You must connect each of the

five speakers to the proper terminal on the

RSX-1056.

Route the wires from the RSX-1056 to the speak-

ers. Leave enough slack so you can move the

components to allow access to the speaker con-

nectors. If you are using banana plugs, con-

nect them to the wires and then plug into the

backs of the binding posts. The collars of the

binding posts should be screwed in all the way

(clockwise). If you are using terminal lugs,

connect them to the wires. If you are attach-

ing bare wires directly to the binding posts,

separate the wire conductors and strip back

the insulation from the end of each conduc-

tor. Be careful not to cut into the wire strands.

Unscrew the binding post collars. Place the

connector lug or the twisted bare wire around

the binding post shaft. Turn the collars clock-

wise to clamp the connector lug or wire firmly

in place.

1. Connect the front right speaker to the bind-

ing posts labeled FRONT/CB/ZONE

RIGHT/2.

2. Connect the front left speaker to the bind-

ing posts labeled FRONT/CB/ZONE LEFT/

3. Connect the center channel speaker to

binding posts labeled CENTER.

4. Connect the surround right speaker to bind-

ing posts labeled SURROUND RIGHT.

5. Connect the surround left speaker to binding

posts labeled SURROUND LEFT.

NOTE

: Be sure that no loose wire strands can

touch adjacent wires or connectors.

After you have connected the speakers, you

need to configure the RSX-1056 for the size

and style of speakers in your system and cali-

brate the relative volume levels of the speak-

ers using the built-in test tones. See the

Setup

section of this manual.

Redirect Feature

The RSX-1056 has a “redirect” feature that

allows you to use the front left and front right

amplifier channels to power center back or

Zone 2 speakers. For example, you might use

a separate Rotel stereo power amplifier to drive

the front speakers and then use the extra am-

plifier channels in the RSX-1056 to power two

center back speakers.

If your system does not have center back speak-

ers, you can also redirect the built-in center

back channel amplifiers to drive two Zone 2

speakers.

To use the redirect feature to power center back

speakers in a 6.1 or 7.1 channel system:

1. Connect the center back speaker in a 6.1

channel system or the center back left

speaker in a 7.1 channel system to the

binding posts labeled FRONT/CB/ZONE

LEFT/1.

2. Connect the center back right speaker to

binding posts labeled FRONT/CB/ZONE

RIGHT/2.

3. Go to the SPEAKER SETUP screen of the

ON-SCREEN MENU system and change

the REDIRECT setting to the center back

channels instead of the front channels.

Connecting a Subwoofer

See Figure 3

To hook up a powered subwoofer, connect a

standard RCA audio cable from either of the

two PREOUT jacks labeled SUB to the input

on the subwoofer’s power amp. Both SUB

outputs provide the same signal. Use either

connection for a single subwoofer. Use both

connections to hook up two subwoofers.

After you have connected the subwoofer, you

need to configure the RSX-1056 to use the sub-

woofer and calibrate the relative volume level

of the subwoofer using the built-in test tones.

See the Setup section of this manual.

Amplifiers

To hook up power amplifiers, connect

an audio cable from each PREOUT jack to the

input of the amplifier channel that will power

the corresponding speaker. In a full home

theater system, you will need to make as many

as seven different connections in addition to

the subwoofer. These connections are labeled

FRONT L &R, CENTER, and REAR L & R. There

Rotel RSX-1056 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info