Bedienungsanleitung Rotel RSX-1056 (Seite 22 von 46) (Englisch)

498117

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

RSX-1056 Surround Sound Receiver

Many of the RR-1050 functions duplicate the

front panel controls. For that reason, we cover

the controls on the remote under appropriate

topics throughout this manual. Letters in gray

boxes next to the name of a function refers to

the labeled illustration of the remote at the

front of this manual.

Using the RR-1050

AUDIO Button

To operate the RSX-1056 with the remote, make

sure that the AUDIO mode is active by press-

ing the AUD button on the remote before you

start. If one of the other buttons (CD, TAPE,

etc.) is pressed, the remote will control another

component, not the RSX-1056. The AUDIO

mode will stay active until another DEVICE/

INPUT button is pressed.

Programming the RR-1050

PRELOAD Button

The RR-1050 is programmed at the factory to

operate the RSX-1056. Should the AUDIO

command set on your RR-1050 not operate

the RSX-1056, the programming may have

been inadvertently changed. To restore the

RSX-1056 programming, press the recessed

PRELOAD button on the remote with the tip

of a ballpoint pen.

NOTE

: Pushing the PRELOAD button will erase

all custom programming and learned com-

mands, restoring the RR-1050 to its factory

condition.

Overview of Buttons

and Controls

This section provides a basic overview of the

buttons and controls on the front panel and

the remote control. Detailed instructions on the

use of these buttons a provided in the more

complete operating instructions in the follow-

ing sections. Buttons or controls identified with

a number appear on the front panel. Those

identified with a letter appear on the remote

control. When both a number and a letter

appear, the control is duplicated on both the

front panel and the remote control.

STANDBY Button

POWER Button

The front panel STANDBY button and the re-

mote control POWER button activate or de-

activate the unit. The rear panel master POWER

switch must be in the ON position for the re-

mote standby function to operate.

ON/OFF Buttons

The power ON and OFF buttons on the re-

mote provide discrete ON and OFF commands

to activate the unit or put it in standby mode.

The rear panel master POWER switch must

be in the ON position for the remote standby

function to operate.

VOLUME Knob

VOLUME Button

The large rocker button on the remote and the

large rotary control on the front panel provide

the master VOLUME control, adjusting the

output level of all channels simultaneously.

MUTE Buttons

Push the MUTE button once to turn the sound

off. An indication appears in the front panel

and on-screen displays. Press the button again

to restore previous volume levels.

NOTE

: Pressing the volume buttons on the re-

mote also cancels the muting function.

DEVICE/INPUT Buttons

The top row of buttons on the front panel plus

the MULTI INPUT button are used to select

source inputs for listening/viewing.

These buttons are duplicated on the remote,

except that the MULTI INPUT button is labeled

EXT and the remote buttons have two functions:

Short press: A short press of any button

changes the device that the remote operates,

but does not change the RSX-1056’s input

selection.

Long press: A longer press changes the re-

mote control device and changes the source

input for listening/viewing in the main room.

NOTE

: A long press of the EXT button changes

the input to the 7.1 channel analog MULTI

INPUT. Pressing the AUD button only changes

the remote device; there is no input source

associated with this button.

D-SLT Button

Press this button to change the digital input

associated with the current source input.

REC Buttons

Press either of these buttons before pressing

(long press on the remote) any DEVICE/IN-

PUT button to select a source for recording.

The signal from the selected source appears

at the TAPE OUT and VIDEO OUT connectors.

ZONE Buttons

Press either of these buttons before pressing

(long press on the remote) any DEVICE/IN-

PUT button to select a source for ZONE 2.

UP/DOWN Buttons

These two buttons on the remote are used to

move the cursor up or down to select lines in

the OSD menus. These buttons are also used

in conjunction with the TONE button to make

CONTOUR/TONE adjustments.

+/– Buttons

These two buttons on the remote are used to

change settings on a selected line in the OSD

menus. Also used for selecting options in some

surround modes.

Speaker Selection Buttons

These three buttons on the remote are used

to select a speaker or group of speakers for

temporary level adjustments. In addition, the

C button is used in conjunction with the UP/

DOWN buttons for temporary adjustment of

group delay/lip synch.

EQ Button

This button on the remote is used to turn on

and off the Cinema EQ feature, a high-cut filter

useful for older movie soundtracks.

TONE Button

This button on the remote is used for tempo-

rary Contour adjustments. It toggles between

high frequency (HF) and low frequency (LF)

modes. Once a mode is selected, the UP/

DOWN buttons are used to make the adjust-

ments to the speaker or speakers selected in

the Contour Setup menu.

NOTE

: Permanent contour adjustments can be

made using the Contour Setup menu.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel RSX-1056 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info