Bedienungsanleitung Rupes MX800 (Seite 11 von 53) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489883

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

BEFORE FREEING JAMMED MATERIAL

- Turn tool “OFF” by releasing trigger switch,

- Wait for all moving parts to stop,

- Unplug the machine.

BEFORE LEAVING THE MACHINE NEVER

LEAVE TOOL RUNNING UNATTENDED

- Turn power off,

- Wait for all moving parts to stop,

- Unplug.

ARNING: The operation of any power tool

can result in foreign objects being thrown into

your eyes, which can result in severe eye dama-

ge. Before beginning tool operation, always wear

safety goggles of safety glasses with side shields

and a full face shield when needed. We recom-

mend Wide Vision Safety Mask for use over eye-

glasses or standard safety glasses with side

shields.

MAKE WORKSHOP CHILD PROOF

- Lock the shop,

- Disconnect master switches,

- Store tool away from children and others not

qualified to use the tool.

Look for this symbol to point out important

safety precautions. It means attention!!! Your

safety is involved.

MOTOR AND ELECTRICALREQUIREMENTS

WARNING: To reduce the risk of electrical

hazards, fire hazards or damage to the tool, use

proper circuit protection. Your machine is wired at

the factory for operation using the voltage shown

above. Connect tool to a power line with the

appropriate voltage and a 16-amp branch circuit.

Use a 16-amp time delay type fuse or circuit

breaker. To reduce the risk of shock or fire, if

power cord is worn or cut, or damaged in any

way, have it replaced immediately.

ELECTRICAL CONNECTIONS

NOTE: The plug supplied on your tool may not fit

into the outlet you are planning to use. Your local

electrical code may require slightly different

power cord plug connections. If these differences

exist refer to and make the proper adjustments

per your local code before your tool is plugged in

and turned on. In the event of a malfunction or

breakdown, grounding provides a path of least

resistance for electric current to reduce the risk of

electric shock. This tool is equipped with an elec-

tric cord having an equipment grounding conduc

tor and a grounding plug, as shown. The plug

must be plugged into a matching outlet that is

properly installed and grounded in accordance

with all local codes and ordinances. Do not modi-

fy the plug provided. If it will not fit the outlet,

have the proper outlet installed by a qualified

electrician.

Improper connection of the equipment grounding

conductor can result in a risk of electric shock.

The conductor with insulation having an outer

surface that is green with or without yellow stri-

pes is the equipment grounding conductor. If

repair or replacement of the electric cord or plug

is necessary, do not connect the equipment

grounding conductor to a live terminal.

If power cord is worn or cut, or damaged in any

way, have it replaced immediately by a qualified

electrician. If the grounding instructions are not

completely understood, or if you are in doubt as

to whether the tool is properly grounded check

with a qualified electrician or service personnel.

ARNING: Do not permit fingers to touch the

terminals of plug when installing or removing the

plug from the outlet to avoid injury or possible

death from electrical shock.

ARNING

: If not properly grounded, this tool

can cause an electrical shock, particularly when

used in damp locations, in proximity to plumbing,

or out of doors. If an electrical shock occurs there

is the potential of a secondary hazard, such as

your hands contacting the mixing paddle.

MOTOR SAFETYPROTECTION

IMPORTANT: To avoid motor damage, this

motor should be blown out or vacuumed frequen-

tly to keep dust from interfering with normal motor

ventilation.

1. Connect this tool to a power source with the

appropriate voltage for your model and a 16-amp

branch circuit with a 16-amp time delay fuse or

circuit breaker. Using the wrong size fuse can

damage the motor.

2. If the motor won’t start, turn the switch off

immediately and unplug the tool.

3. If the motor suddenly stalls while mixing, relea-

se the trigger switch, unplug the tool.

The motor

may now be restarted.

4. Fuses may "blow" or circuit breakers may trip

frequently for the following reasons:

Motor Is Overloaded-Overloading can occur

if you feed too rapidly or make too many

start/stops in a short time.

b. Line voltages should not be more than 10%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rupes MX800 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info