Bedienungsanleitung Rupes MX800 (Seite 12 von 53) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489883

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

above or below the nameplate voltage. For heavy

loads, however, the voltage at motor terminals

must equal the voltage specified for your model.

5. Most motor troubles may be traced to loose or

incorrect connections, overload, low voltage

(such as small size wire in the supply circuit) or

to overly long supply circuit wire. Always check

the connections, the load and the supply circuit

whenever motor doesn’t work well. Check wire

sizes and length with the

Wire Size Chart

WIRE SIZES

NOTE: Make sure the proper extension cord is

used and is in good condition. Use only 3-wire

extension cords that have 3-prong grounding

plugs and 3-pole receptacles that accept the too-

l’s plug. The use of any extension cord will cause

some loss of power. To keep this to a minimum

and to prevent overheating and motor burnout,

use the table at right to determine the minimum

wire size (A.W.G.) extension cord.

UNPACKING AND CHECKING CONTENT

Unpacking

ARNING: To reduce the risk of injury from

unexpected starting or electrical shock, do not

plug the power cord into a power source outlet

during unpack¬ing and assembly. This cord must

remain unplugged whenever you are work¬ing

on the tool.

Your tool is shipped complete in one box.

- Remove the tool and all loose parts from the

carton.

- Place all parts on a secure, stationary work sur-

face and look the machine over carefully.

List of Loose Parts

The following parts are included:

NOTE

: Before beginning assembly, check that all

parts are included. If you are miss

ing any part,

do not assemble the machine. Sometimes small

parts can get lost in packaging material. Do not

throw away any packaging until tool is put toge-

ther

. Check packaging for missing parts. A com-

plete parts list (Repair Parts) is at the end of the

manual. Use the list to identify the number of the

missing part.

ARNING: If any parts are missing do not

operate your Electric Stirrer until the missing

parts are replaced. Failure to do so could result

in possible serious injury.

Part or Assembly Qty

Basic Assembly 1

Wrench 1

Operator’s Manual 1

BASIC OPERATION

Switch

On/Off Trigger

Switch - To start

the machine,

squeeze the trig-

ger switch.

Release the trig-

ger switch to stop

the motor. This

machine is equip-

ped with a lock-on

arrestor pin. If

continuous operation is required, squeeze the

trigger and press the arrestor pin. To stop, squee-

ze and release the trigger switch.

Speed Adjustment

By turning the

thumb operated

adjustor wheel,

the speed may be

adjusted electroni-

cally for best

mixing performan-

ce in a given

medium.

Gear Changes

On 2 speed range

models, there is a

gear selector sli-

der on the gear-

box housing. Use

low speed range

for best torque in

extremely viscous

media. To select a

gear range, first

shut down the

machine. Push in on the selector slider against

Total Extension Cord

Cord Length Size

(feet) (AWG)

25 16

50 12

100 10

150 8

200 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rupes MX800 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info