Bedienungsanleitung Ryobi css 1801m one (Seite 15 von 137) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383100

Zoom out

Zoom in

Vorherige Seite

1/137

Nächste Seite

OPERATION

APPLICATIONS

You may use this tool for the following purposes:

Note: Most of these applications require different types

of bits. Be sure to use the right bit for your tool.

■ Cutting electrical outlet openings in drywall or

wood paneling. It is recommended to use a 3.2 mm

bit for cutting wood paneling.

■ Creating decorative wood accents

■ Cutting tile

CAUTION

To prevent damage to the battery pack, remove

the battery pack from the charger immediately if

no LED comes on. Return the battery pack and

charger to your nearest service centre for

checking or replacing. Also, if you are removing

the battery pack from the charger and no LEDs

are on, return both the battery pack and the

charger to your nearest service centre. Do not

insert another battery pack into the charger.

Adamaged charger may damage a battery pack.

Do not abuse power tools. Abusive practices can damage

tool as well as workpiece.

WARNING

Do not attempt to modify this tool or create

accessories not recommended for use with

this tool. Any such alteration or modification is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

TO INSTALL BATTERY PACK (NOT INCLUDED)

(Fig. 5)

■ Place battery pack on the spiral saw.

■ Align raised rib on battery pack with groove in saw’s

battery port.

■ Make sure the latches on each side of the battery

pack snap in place and that battery pack is secured

on the tool before beginning operation.

CAUTION

When placing battery pack in the tool, be sure

raised rib on battery pack aligns with the bottom

of the drill and latches into place properly.

Improper installation of the battery pack can

cause damage to internal components.

TO REMOVE BATTERYPACK (NOT INCLUDED)

(Fig. 5)

■ Locate latches on side of battery pack and depress

both sides to release battery pack from the spiral saw.

■ Remove battery pack from the spiral saw.

STARTING/STOPPING SPIRALSAW (Fig. 6)

Follow these directions when starting and stopping the

spiral saw.

■ To start: Depress switch to the On ( I ) position.

■ To stop:Depress switch to the Off ( O ) position.

CAUTION

We suggest that you practice with your spiral

saw before installing a bit and making cuts.

OPERATING THE SPIRAL SAW (Fig. 7)

■ Hold spiral saw firmly with both hands.

■ Start spiral saw.

■ Tilt spiral saw at a 45° angle.

■ Plunge bit into material using guide ring as a pivot.

■ Raise spiral saw slowly to a 90° angle.

■ Begin cutting.

DANGER

Do not cut electrical outlet openings with live

electrical wires. Do not cut walls that may have

live electrical wiring behind them. Shut off

breakers or remove fuses to disconnect the

circuit. Always hold the tool by its motor housing.

USING CIRCLE CUTTER (Fig. 8)

■ Assemble circle cutter if necessary. Refer to

“Assembling Circle Cutter” in this manual.

■ Attach circle cutter to spiral saw if necessary. Refer to

“Attaching Circle Cutter” in this manual.

■ Adjust depth of cut if necessary. Refer to “Adjusting

Depth Of Cut” in this manual.

■ Loosen pivot point knob.

■ Move pivot point knob to desired diameter dimension.

■ Tighten pivot point knob.

■ Start spiral saw.

■ Cut a pilot hole in the centre of the intended circle.

■ Line up pivot point knob with the lead hole.

■ Begin cut, applying moderate, steady pressure.

■ Hold the spiral saw firmly with one hand and the

handle with the other.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

CSS-1801DM 29/07/05 10:52 Page 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi css 1801m one Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info