Bedienungsanleitung Ryobi css 1801m one (Seite 16 von 137) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383100

Zoom out

Zoom in

Vorherige Seite

1/137

Nächste Seite

OPERATION

CAUTION

Too much force causes heat build up, which can

shorten the life of the bit.

■ Work in a clockwise direction, continuing back to the

starting position.

■ Stop spiral saw.

ADJUSTMENTS

WARNING

To prevent accidental starting that could cause

serious personal injury, always remove the

battery pack from the tool when making

adjustments.

INSERTING/REMOVING BITS (Fig. 9)

■ Remove battery pack from spiral saw.

CAUTION

To prevent damage to the spindle or spindle lock,

always allow motor to come to a complete stop

before engaging spindle lock.

■ Depress spindle lock.

■ Loosen collet nut by turning counterclockwise with the

wrench provided.

WARNING

If you are changing a bit immediately after use,

be careful not to touch the bit or collet with your

hands or fingers. They will get burned because

of the heat buildup from cutting. Always use the

wrench provided.

■ To insert bit: Insert shank end of bit into collet.

■ To remove bit: Remove bit once collet nut is loose.

Note: The collet is machined to precision tolerances

to fit bits with 6.35 mm diameter shanks. To use bits

with 3.2 mm shank bits, insert the 3.2 mm adaptor

into the 6.35 mm collet.

■ Tighten collet nut securely by turning clockwise with

the wrench provided.

WARNING

If the collet nut is not securely tightened,

the bit may detach during use causing serious

personal injury.

■ Release spindle lock.

WARNING

Do not use bits with undersized shanks.

Undersized shanks will not tighten properly and

could be thrown from the tool causing injury.

ADJUSTING DEPTH OF CUT (Fig. 10)

■ Remove Battery Pack From spiral saw.

■ Loosen adjusting knob by turning counterclockwise.

■ Move depth adjustment ring to desired position.

■ Tighten adjusting knob by turning clockwise.

MAINTENANCE

WARNING

When servicing, use only identical replacement

parts. Use of any other parts may create a

hazard or cause product damage.

WARNING

Always wear safety goggles or safety glasses

with side shields during power tool operation or

when blowing dust. If operation is dusty, also

wear a dust mask.

WARNING

To avoid serious personal injury, always remove

the battery pack from the tool when cleaning or

performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts.

Most plastics are susceptible to damage from various

types of commercial solvents and may be damaged

by their use. Use clean cloths to remove dirt, dust, oil,

grease etc.

WARNING

Do not at any time let brake fluids, gasoline,

petroleum-based products, penetrating oils etc.,

come in contact with plastic parts. Chemicals can

damage, weaken ordestroy plastic which may

result in serious personal injury.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts

should be replaced at a Authorised Service Centre.

BITS

Get faster and more accurate cutting results by keeping

bits clean. Remove all accumulated build-up from bits

after each use. Replace bits when they become dull.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

CSS-1801DM 29/07/05 10:52 Page 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ryobi css 1801m one Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info