7
43-COMPACT (SA1741)
Pos: 12.7 /Inne
Pos: 12.8 /Innecx @ 5
1 Safety control bar for motor stop
2 Setting handle for adjusting cuttarrying handle at the back) with push-
button
3 Tank
4 Engine
5 Air
6 Cutting height display
7 Carrying handle
8 Spark
9 Exhaust protection grid
10 Belt drive covers
11 Oil refill neck with dipstick tank cap
12 Ejector
13 Starter cable handle
Pos: 12.9 /Inne
All models
Pos: 13.1 /----
Pos: 13.2 /Inne
8 PREPARATION
Pos: 13.3 /Innenteil415217 @ @ 1
The following unit parts are included in the package for mower assembly:
• Mower with pre-assembled guide bar
• Grass catch, collecting bag frame
• Tool bag containing the following:
– Operator’s manual with Declaration of Conformity
– Warranty conditions (depending on model)
– Diverse attachment parts.
Should a part be missing, please contact your professional dealership.
Pos: 13.4 /Innenteil/Vorbereitende Arbeiten/Vor Montage... Holm und...Starterseilhalter...Zündkerzenstecker abziehen! Hinweis @ 32\mod_140
NOTE
Always remove the spark plug connector befor
cable holder. Following assembly,
the spark plug connector back in place.
Pos: 13.5 /Innecx @
Opening out the handle (Illustrati
Pos: 13.6 /Inne 508855 @ @ 1
IMPORTANT
Make sure the throttle cables are not kinked or j
handlebars.
Pos: 13.7 /Inne21.docx @ 1413
– Pull on the handlebar which is collapsed in a Z-shape upwards into place A1 .
– When the top and bottom parts of the handlebar are on the same level, firmly
tighten the wing nuts by hand E1.
– On the bottom part of the handlebar, swivel the ends with the toothed f
towards the back as far as necessary until they click into the toothed recess on the
mower housing B1 .
This allows three different handlebar heights to be set.
– Tighten the wing nuts on both sides by hand B1 .
– Insert the cable harness (electro-start) and the throttle cable into the cable guides.
This prevents the cable harness or throttle cable being jammed when the
handlebar is folded down E1 .
– Fix the throttle cable on the left lower bar using the shorter cable ties from the tool
bag.
Pos: 13.8 /_128
CAUTION
When you activate the bar height
B1 used to secure the bar bottom to the housing (only loosen sufficiently to
ensure that the bar can be moved freely) and snapping the toothed plast
adaptations from the cut-
upsetting of the bar may occur
between the bar bottom and t
Pos: 13.9 /Inne 1
Handle starter assembly (Il
Pos: 13.10 /In08 @ @ 1
– Remove the starter cable holder (1) from the tool bag.
– Unscrew the nut until the two halves can be pushed over t
– There is a sticker (2) on the top bar showing the position of the starter cable
holder.
NOTE
For reasons of safety, the starter cable holder may only be fitted in the
prescribed positi
– Push the motor stop safety control bar (3) onto the top part of the bar (4) and hold
it tight, pull the starter cable (5) out and insert it into the starter cable holder.
– Fit the two halves (6) together, tighten the nut
cable popping out.
The starter cable holder must be fitted / aligned in such a way that t
is freely accessible and does not rub against any other parts.
Pos: 13.11 /.docx @
Attaching the grass collector to the mower (I
Pos: 13.12 /In
– Insert the collection bag frame with the bar first into the grass catch. Align the
upper seams of the grass catch on the bar.
– Press the holding profile onto the frame of the collection bag fr R1 .
– Open the ejection flap of the mower upwards.
– Lift the grass collection bag on the carrier bar, insert the chut R1 on the
collection bag opening into the ejection flap and hang the grass collection bag with
the two side hooks to the top of the mower housing S1 .
– Fold the ejection flap onto the grass collection bag.
Pos: 13.13 /In@ 2 @ 1
Adjusting the cutting height (Illustr
Pos: 13.14 /In
Safety instruction!
See table for explanation of symbols page 3
Pos: 13.15 /In
The cutting height is adjusted behing the motor.
– Press the grey push button with your thumb and lift or lower the mower handle to
bring it into the required position.
– Release the push button: the lever now engages in the required cutti
– The marking on the left of the housing shows the adjusted cut
Pos: 13.16 /Innenteidocx @ 16
IMPORTANT
Mowing at the lowest cutting height should only be carri
lawns!
Please observe that the lower cutting height settings may only be used for
optimal conditions.
damaged and under certain circumstances it
Besides the cutting height, also the moving speed influences the cutting pattern
and collection result. Adapt the cutting height and moving speed to the gr
height to be cut.
Pos: 13.17 /521.do
Fitting the cable harness (onl
Pos: 13.18 /In
Fix the pre-assembled cable harness to the right lower handle using the enclosed
longer cable clips in such a way that the plug can be fitted to the contacts of
lock without tension.
Pos: 13.19 /InU1) MUST
Fitting the charged starter batt
(Illustration V1 + U1 )
Pos: 13.20 /.docx @ 35
– Place the battery on the battery holder behind the motor from the side, ensuring
that the connection cable points t
– Remove the battery cover and M6x120 screws from the tool bag.
– Place the cover on the battery (holding the battery at an angle) and f
using the two screws V1 .
– Connect the battery plug with the counter-plug of the cable form bef
U1 .
