Bedienungsanleitung Samson MDR16 (Seite 7 von 32) (Englisch)

24757

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1 or AUX 2 bus by using the

AUX1/2 switch

which lights

when set to AUX2.

LOW FREQUENCY

(Stereo Channels)

- Controls the

low band of the Channel Equalizer, +/- 15 dB at 80Hz.

23 HIGH FREQUENCY (Stereo Channels)

- Controls the

high band of the Channel Equalizer, +/- 15 dB at 12KHz.

24 MIC LINE (combie)

– Combination

1/4-inch

XLR

Input

connector for the Line or Low-Noise Microphone Inputs

on the even number stereo channels.

25 MIC LINE

(combie)

–

Combination

1/4-inch

XLR

Input connector for the Line or Low-Noise Microphone

Inputs on the odd number stereo channels.

26 OUTPUTS 3 / 4

- Balanced outputs on 1/4-inch TRS con-

nectors that carry the signals from the 3 and 4 mix bus.

27 OUTPUTS 1 / 2

- Balanced outputs on 1/4-inch TRS con-

nectors that carry the signals from the 1 and 2 mix bus.

28 INSERT (Bus 1 / 2)

Send and return patch point on TRS

(TIP/RING/SLEEVE) jack for interfacing external effects

processors on the

1 & 2 mix bus.

29 AUX RET 1 (L/R Jacks)

– Balanced inputs on 1/4-inch

TRS connectors for connecting external line level signals

like those from external effects processors.

30 AUX 1

– Output connector for Auxiliary 1.

31 INSERT (Bus 3 / 4)

Send and return patch point on TRS

(TIP/RING/SLEEVE) jack for interfacing external effects

processors on the

3 & 4 mix bus.

32 AUX 2

– Output connector for Auxiliary 2.

33 MIX INSERT

– Send and return patch point on TRS (TIP/

RING/SLEEVE) jack for interfacing external effects proces-

sors on the main mix.

34 CONTROL ROOM

– Left and Right output connectors for

connecting a monitor system.

35 MIX LEFT

– Balanced output on 1/4-inch TRS connector

that carries the signals from the Left Main mix bus.

36 MIX RIGHT

– Balanced output on 1/4-inch TRS connec-

tor that carries the signals from the Right Main mix bus.

37 AUX RET 2 (L/R Jacks

)

– Balanced inputs on 1/4-inch

TRS connectors for connecting external line level signals

like those from external effects processors.

38 MONO OUT LEVEL

– Used to set the volume of the

MONO mix.

39 2 TK LEVEL

- Control used to adjust the volume of the

2-track input.

40 2 TRACK INPUTS

– Connect a DAT, Cassette, Mini Disk or

Hard Disk Recording system.

41 2 TRACK OUTPUTS

– Connect a DAT, Cassette, Mini Disk

or Hard Disk Recording system.

42 Graphic Equalizer

– Provides dual 9-Band equalization

assignable to either the main or Aux 1 mix.

Front Panel Layout

1 CLIP

– Red LED will illuminate, indicating when the GAIN

, EQ, or channel fader control has been adjusted too

high.

2 GAIN

– Used to set the input level of the mic pre and

line input.

3 HIGH FREQUENCY

- Controls the high band level of the

Channel Equalizer, +/- 15 dB.

4 MID CUT & BOOST

- Controls the level of mid-range ,+/-

15 dB at the frequency set by the Mid Frequency control.

5 MID FREQUENCY

- Used to set the center point of the

mid band of the Channel Equalizer from 100 Hz to 5KHz.

6 LOW FREQUENCY

- Controls the low band of the

Channel Equalizer, +/- 15 dB at 80Hz.

7 LOW CUT

– Bass roll-off switch at 80Hz used to eliminate

unwanted low end rumble and hum.

8 AUX 1

– Pre-fader auxiliary send that can be used with

an external effects processor, or to create a cue or moni-

tor mix.

9 AUX 1 PRE/POST

- This LED back-lit switch is used to

select the point in the audio path that the channel’s

signal is sent to the AUX 1 bus, either before or after the

input fader.

10 AUX 2/DSP

– Post-fader auxiliary send connected to the

internal 24 BIT DSP effect processor and can also be used

with an external effects processor.

11 PAN

– Controls the channel’s balance between left and

right in the stereo bus.

12 SOLO Switch (Mono Channels)

– Back-lit LED switch

used to assign the channel to the SOLO bus.

13 1/2 ASSIGN

– LED, back-lit switch used to assign the

channel to the1/2 output bus.

14 3/4 ASSIGN

– LED, back-lit switch used to assign the

channel to the 3/4 output bus.

15 FADER

– 60 mm audio taper fader provides smooth con-

trol over level changes.

16 MIC INPUT

– XLR input connector for the input chan-

nel’s Low-Noise Microphone pre-amp.

17 INSERT (mono input channels)

– Send and return

patch point on TRS (TIP/RING/SLEEVE) jack for interfac-

ing external effects processors.

18 LINE INPUT

– 1/4-inch TRS (TIP/RING/SLEEVE) input con-

nector for the input channel’s balanced Line level inputs.

19 PAN (stereo inputs)

– Controls the channel’s balance

between left and right in the stereo bus.

AUX (stereo channels)

– Depending on the position of

the AUX 1/2 switch, this control knob will send signal to

the Aux 1 or Aux 2 bus.

21 AUX 1/2 Switch (Stereo Channels)

- The auxiliary send

on the Dual/Mono channels can be set to either the AUX

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR16 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info