Bedienungsanleitung Samson MDR16 (Seite 9 von 32) (Englisch)

24757

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

GAIN

The MDR16’s pre-amp stage has a variable GAIN control with a range of 5 to 60dB

on the MIC input and –26 to +26dB on the LINE input.

CLIP LED

The MDR16’s MIC/LINE pre-amp also includes a CLIP LED which, when illuminated,

indicates that the signal is peaking or overloading. To reduce distortion, lower the

GAIN, EQ, or fader control to keep this LED from staying on.

HF (HIGH FREQUENCY)

12kHz +/- 15dB shelving type. The channel’s frequency response is flat when the

knob is in the "12:00" position. Rotating the knob towards the right will boost the

corresponding frequency band by 15dB, and rotating it towards the left will cut

the frequency by 15dB.

MID (CUT & BOOST)

The MID CUT & BOOST knob is used in conjunction with the MID FREQUENCY

knob to create the tonal shape in the mid-range frequency when using the mono channel’s equalizers. You can

adjust the frequency on the mid-range control with the MID SWEEP knob, and use the MID CUT & BOOST to either

boost or cut that frequency by plus or minus 15dB.

MID FREQUENCY

The MID FREQUENCY is a control enabling you enhanced capabilities in the tonal shaping of the input channel sig-

nal. Thanks to the MID FREQUENCY control, you have a variable mid-range equalizer, allowing you to pin point the

exact frequency you want to boost or cut. The MID SWEEP has a “fixed Q” of two octaves (the amount, or width, of

frequencies around the center point that are effected by the MID CUT & BOOST control) and can be set in a range

from 100Hz to 5kHz.

LF (LOW FREQUENCY)

80Hz +/- 15dB shelving type The channel’s frequency response is flat when the knob is in the "12:00" position.

Rotating the knob towards the right will boost the corresponding frequency band by 15dB, and rotating it towards

the left will cut the frequency by 15dB.

LOW CUT FILTER

Each of the MDR16’s channels include a LOW CUT (or high pass) filter which rolls off the low frequencies from 80Hz

and below at the rate of 18dB per octave.



























































































Controls and Functions

MONO INPUT CHANNEL SECTION

The following section details each part of the MDR16ʼs MONO INPUT CHANNELS including the GAIN control, CLIP LED,

3-BAND EQ, AUX sends, PAN and LEVEL controls.

The input channels one through eight on the MDR16 feature high quality,

discrete transistor pre-amps providing transparency and extended dynamic range. The inputs feature a standard XLR mic connec-

tor for microphone level signals, and a standard 1/4" phone connector, either balanced (TRS – TIP/ RING/SLEEVE) or unbalanced (TS

– TIP/SLEEVE) for line level signals.

CHANNEL EQUALIZER

The MDR16 input channels feature a 3-band, swept-mid equalizer allowing you to

adjust the high, mid, and low frequencies independently on each channel. The fre-

quency centers, range of boost or cut, and equalizer type for each band are as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Samson MDR16 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info