Bedienungsanleitung Sangean ATS-909X2 (Seite 10 von 19) (Englisch)

797034

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

USING SCAN TUNING

The scan tuning feature of the ATS-909X2 can be used

on any band to automatically scan from the current

frequency to the nearest strong station with a higher /

lower frequency.

Follow these steps to use the scan feature:

1. Turn on the radio using the Power button (10).

2. Select the desired waveband by pressing the

corresponding button.

3. Press and hold one of the Tuning Up / Down buttons (18).

4. The radio now automatically scans for the nearest station

with a strong signal and a higher / lower frequency and

will play this station once it has been found.

5. Repeat step 4 to find to tune to other radio stations.

NOTE

The sensitivity of the scan tuning feature can be

adjusted by setting the squelch level. See "SETTING

THE SQUELCH LEVEL" section in chapter 5 for more

information.

USING MANUAL TUNING

Manual tuning can be used on any band to either input the

frequency of a radio station directly or to manually tune or

fine-tune to a station using small steps.

DIRECT TUNING

Follow these steps to directly tune to a radio station of

which you know the frequency:

1. Turn on the radio using the Power button (10).

2. Press the Freq button (25).

3. Use the numeric buttons (19) and the Decimal point

button (32) to enter the frequency.

Examples:

FM 107.85MHz: Press Freq (25) → 1 → 0 → 7 → . →

8 → 5 → Enter

SW 25785kHz: Press Freq (25) → 2 → 5 → 7 → 8 → 5

→ Enter

Or Press Freq (25) → 2 → 5 → . → 7 → 8 → 5 →

Enter

AIR 123.450MHz: Press Freq (25) → 1 → 2 → 3 → .

→ 4 → 5 → Enter

AM 1620kHz: Press Freq (25) → 1 → 6 → 2 → 0 →

Enter

LW 257kHz: Press Freq (25) → 2 → 5 → 7 → Enter

NOTE

If the desired frequency is on the FM band, a decimal

point must be added when inputting the frequency.

MANUAL TUNING

To tune to a radio station of which you know the frequency

or to fine-tune to a station, follow these steps:

1. Turn on the radio using the Power button (10).

2. Select the desired waveband by pressing the

corresponding button.

3. Use the Rotary Tuning knob (16) or Tuning Up / Down

buttons (18) to tune to a higher / lower frequency.

SETTING THE TUNING STEP

When using manual tuning, the frequency change per

tuning step using the Rotary Tuning knob (16) and the FM

tuning step using the Tuning Up / Down buttons (18) can

be adjusted.

To adjust the Rotary Tuning knob (16) tuning step for the

SW, MW, LW, FM and AIR band, simply press the Step

button (17) when listening to a radio station. The Tuning

step indicator (O) on the display shows which tuning step

is currently selected. In addition, you can press and hold

the Step button (17) to disable tuning with the Rotary

Tuning knob (16). Hold the Step button (17) again to

enable tuning with the Rotary Tuning knob (16) again.

To adjust the FM tuning step of the Tuning Up / Down

buttons (18), follow these steps:

1. Press and hold the Menu button (29) to open the menu.

2. Use the Rotary Tuning knob (16) to select "FM STEP"

in the Text display (U).

3. Press the Step button (17) or Enter button (30) to start

configuring the setting.

The current FM tuning step will now blink in the Text

display (U).

4. Use the Rotary Tuning knob (16) to select 50kHz,

100kHz or 200kHz.

5. Press the Step button (17) or Enter button (30) to

confirm your choice.

6. Press the Menu button (29) to close the menu.

The MW / AM tuning step can be adjusted using the MW

/ AM tuning step switch (48), which is located inside the

battery compartment. This switch can be placed in either

the 9kHz or 10kHz position. In Europe and most other

parts of the world this switch must be placed in the 9kHz

position, while in America this switch must be placed in

the 10kHz position.

Finally, the ATS-909X2 also features a quick tuning

feature. This feature can be used by pressing and holding

the Enter button (30) while simultaneously rotating the

Rotary Tuning knob (16). Quick tuning allows for even

larger frequency steps, but it can only be used on the AIR,

FM and SW bands.

The following table shows the available tuning steps for

the Rotary Tuning knob (16) and the Tuning Up / Down

buttons (18) for each of the wavebands:

AIR FM LW MW SW

Rotary

Tuning

knob

STOP 0 0 0 0 0

FAST 25kHz 100kHz 9kHz 9kHz

10kHz 5kHz

SLOW 5kHz 50kHz 1kHz 1kHz 1kHz

Tuning Up /

Down (scan or

seek)

25kHz

50kHz

100kHz

200kHz

9kHz 9kHz

10kHz 5kHz

Quick Tuning 1MHz 1MHz - - 100kHz

STEREO RECEPTION

The ATS-909X2 is designed to receive FM stereo

broadcasts. When the radio is tuned to an FM station of

sufficient strength, the FM stereo indicator (Ab) will be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean ATS-909X2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sangean ATS-909X2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info