Bedienungsanleitung Sangean ATS-909X2 (Seite 13 von 19) (Englisch)

797034

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

The SW meter band indicator (Q) will now be blinking

on the display.

4. Press one of the numeric buttons (19), the Memo

button (24), the Freq button (25) or the Cancel button

(31) to select the corresponding meter band.

The following table shows which buttons (mentioned

in step 4 above) correspond to which meter band and

frequency range:

USER INPUT METER BAND FREQUENCY

RANGE (MHz)

1 120m 2.300-2.495

2 90m 3.200-3.400

3 75m 3.900-4.000

Freq 60m 4.750-5.060

4 49m 5.900-6.200

5 41m 7.100-7.350

6 31m 9.400-9.990

Memo 25m 11.600-12.100

7 21m 13.500-13.870

8 19m 15.100-15.800

9 16m 17.480-17.900

●15m 18.900-19.020

0 13m 21.450-21.750

Cancel 11m 25.600-26.100

NOTE

After selecting a meter band, the selected band will

remain on the display as long as the radio is tuned

within this meter band. When using scan tuning,

the automatic scan will also loop within the selected

meter band, unless you continue pressing one of

the Tuning Up / Down buttons (18) till the frequency

crosses the range of the meter band.

SINGLE SIDE BAND (SSB) RECEPTION

– SW / MW / LW

SSB is very popular among ham and business radio users

because of its efficiency. Amateurs who use SSB and

transmit below 10MHz generally use the lower side band

(LSB), while amateur and commercial stations transmitting

above 10MHz generally use the upper side band (USB).

Your ATS-909X2 is capable of receiving all USB and LSB

transmissions.

To receive SSB stations:

1. Turn on the radio using the Power button (10).

2. Rotate the AM RF Gain jog dial (40) to the maximum

position.

3. Select the SW, MW, or LW band by pressing the

corresponding button.

4. Tune to an SSB station in accordance with earlier

instructions.

5. As soon as you have tuned to an SSB station (you will

not be able to clearly hear any speech), switch to SSB

reception by pressing the SSB button (6) repeatedly to

switch between AM, USB and LSB. The SSB indicator

(G) on the display shows which band is currently

selected.

6. After selecting the correct mode, use the STEP button

(17) to select SLOW stepping and then use the Rotary

Tuning knob (16) to fine-tune to the station.

NOTE

The minimum tuning step is set to 20Hz by default, but it

can be changed to 10Hz in the menu. Refer to the next

section for more information on setting the SSB tuning

step.

SETTING THE SINGLE SIDE BAND

TUNING STEP – SW / MW / LW

When using manual tuning on either of the single side

bands, the frequency change per tuning step when using

the Rotary Tuning knob (16) can be adjusted by following

these steps:

1. Press and hold the Menu button (29) to open the menu.

2. Use the Rotary Tuning knob (16) to select "SSB STEP"

in the Text display (U).

3. Press the Step button (17) or Enter button (30) to start

configuring the setting.

The current setting will now blink in the Text display (U).

4. Use the Rotary Tuning knob (16) to select 10Hz or

20Hz.

5. Press the Step button (17) or Enter button (30) to

confirm your choice.

6. Press the Menu button (29) to close the menu.

The following table shows the available tuning steps for

the Rotary Tuning knob (16) and the Tuning Up / Down

buttons (18) for the single side bands:

LSB / USB

LW MW SW

Rotary

Tuning

knob

STOP 0 0 0

FAST 1kHz 1kHz 1kHz

SLOW 20Hz /

10Hz

20Hz /

10Hz

20Hz /

10Hz

Tuning Up / Down 9kHz 9kHz /

10kHz 5kHz

SETTING THE BANDWIDTH

The Bandwidth Control switch (13) allows you to choose

whether the bandwidth for the various bands should be

automatically set or manually set. When the switch is

placed in the manual position, the Bandwidth Control

button (26) can be used to change the bandwidth on the

SW, MW, LW, FM and AIR bands.

A wide bandwidth can increase sound quality when

receiving a strong signal, while a narrow bandwidth can

make it easier to receive weak signals and overcome

problems caused by interference. When selecting the

narrowest bandwidth on the FM band, stereo playback is

not always available.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sangean ATS-909X2 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sangean ATS-909X2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info