Bedienungsanleitung Satel CA-10 (Seite 5 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 3

EOL, 2EOL/NC, 2EOL/NO. The use of 2EOL configuration enables the panel to

simultaneously control the detector and its tamper circuit by means of one pair of wires.

The zones can perform the following functions in the system:

0 – entry/exit – the violation of which, when in the armed mode, will start countdown of the entry delay

time and will enable the delay mechanism for INTERIOR DELAY type zones (violation of an

INTERIOR DELAY zone without prior violation of the ENTRY/EXIT zone will trigger an alarm

immediately). Upon violation, a “zone violation” code is sent to the report station (it is possible to skip

sending this message), and, after counting down the "entry delay time" and triggering the alarm

- a “zone alarm” code. The "entry delay" countdown can be signaled in the keypad. It is possible to

define automatically bypassing zones if no ENTRY/EXIT zone is violated during the exit delay time”.

Because of its additional functions, this zone type cannot be used as a common zone for several

partitions.

1 – delay – when violated in the armed mode, it starts delay countdown, after which an alarm is triggered.

It will not occur if the zone is disarmed before completion of the delay countdown. Upon violation,

a “zone violation” code is sent to the report station (it is possible to skip sending this message), and,

after counting down the "entry delay time" and triggering the alarm – a “zone alarm” code. The delay is

not signaled in the keypads.

2 – interior delay – when violated in the armed mode after previous violation of the ENTRY/EXIT zone, it

behaves like a DELAY zone. When violated in the armed mode without previous violation of the

ENTRY/EXIT zone, it behaves like an INSTANT zone.

3 – instant – when violated in the armed mode, it immediately triggers an alarm and sends a ”zone alarm”

message to the monitoring station.

4 – day/night – when violated in the armed mode, it behaves like an INSTANT zone, while when

disarmed, it will signal violation in the keypad (unless the signaling is disabled) and send a “zone

violation” code to the station.

5 – counting L1 – when violated in the armed mode, it increases the status of the first of three violation

counters (a „zone violation” code is sent to the station), until the number of violations specified for that

counter is exceeded (programming in FS7). Then, the violation triggers an alarm (a „zone alarm” code

is sent to the report station). The violation counter is reset after 30 seconds since the first violation.

It is possible to program another counter count-up time (FS123). If the preset number of violations is

not reached within this time, there will be no alarm. More than one zone can be define as “counting L1”.

Violations of those zones will be summed up. Violation of the counting zone in armed mode can be

signaled in the keypad in the same way as for the DAY/NIGHT zone.

6 – counting L2 – operation identical as for the "counting L1", but changes the status of the second of the

three counters.

7 – counting L3 – operation identical as for the "counting L1", but changes the status of the third of the

three counters.

8 – 24H audible – armed all the time, irrespective of whether the partition it is assigned to is armed, or not.

Each violation of this zone will trigger alarm on the BURGLARY ALARM type outputs, in the keypad, and

will send a “zone alarm” code. It makes possible to create tamper circuits and panic buttons.

9 – 24H auxiliary – armed all the time, irrespective of whether the partition it is assigned to is armed, or

not. Each violation of this zone will trigger an alarm in the keypad and will send a “zone alarm” code. It is

intended for connecting detectors not related to the burglary alarm, such as gas or flooding sensors, etc.

10 – 24H silent – armed all the time, irrespective of whether the partition it is assigned to is armed, or not.

Violation of this zone will only send a “zone alarm” code to the monitoring station.

11 – 24H fire – armed all the time, irrespective of whether the partition it is assigned to is armed, or not;

intended to manage the fire detectors.

If the control panel contains an output programmed as the FIRE DETECTORS POWER SUPPLY,

violation of the zone will actuate the alarm verification mechanism and will signal alarm in the keypad.

To perform the verification, disconnect momentarily power supply to the fire detectors and check,

whether after reconnection of power supply the violation will be repeated within 90 seconds. If that’s

the case, the control panel will send a „zone alarm” message to the monitoring station, activate the

FIRE ALARM and FIRE/BURGLARY ALARM outputs, and trigger the fire alarm (intermittent signal) in

the keypad.

If there are no FIRE DETECTORS POWER SUPPLY outputs, the zone violation will immediately send

a „zone alarm” code to the monitoring station, activate the FIRE ALARM and FIRE/BURGLARY

ALARM type outputs, as well as trigger the fire alarm (intermittent signal) in the keypad.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info