Bedienungsanleitung Satel CA-10 (Seite 7 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 5

the source). It is also possible to indicate (in the output options) the partition the output is associated

with. If this is the case, the zone alarms will be limited to those from the zones belonging to the

partition indicated. When the "list of outputs" is empty and no partitions are indicated, the output reacts

to all alarms (except for the fire alarms).

The output can remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or

until the alarm is cleared by the user. During its operation, it can every second change its state

(pulsate).

2 – fire/burglary alarm – the output starts on detecting by the control panel of a burglary alarm

(continuous signal) and/or a fire alarm (intermittent signal). The output operation can be limited to the

indicated "list of outputs" or a specific partition (identically as for the 1 output type). The output can

remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is

cleared by the user.

3 – fire alarm – the output starts when the control panel detects a fire alarm. Such an alarm is triggered by

fire zones or the user (through the FIRE ALARM function). The output operation can be limited to the

specified "list of outputs" or particular partitions (identically as for the 1 output type), indication of any

zones other than the fire ones having no sense, as they would not generate a fire alarm. The output

can remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the

alarm is cleared by the user. During operation, it can every second change its state (pulsate).

4 – keypad alarm – the output starts on detecting any keypad alarm (FIRE, PANIC, AUX., keypad tamper

alarms). The output operation can be limited to the alarms from specified partitions. The output can

remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is

cleared by the user. During its operation, it can every second change its state (pulsate).

5 – keypad fire alarm – the output starts on triggering the fire alarm by the user (with the FIRE ALARM

function). The output operation can be limited to the alarms from specified partitions. The output can

remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is

cleared by the user. During operation, it can every second change its state (pulsate).

6 – keypad panic alarm – the output starts on triggering the PANIC alarm by the user. The output

operation can be limited to the alarms from specified partitions. The output can remain active for a

specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is cleared by the

user. During operation, it can every second change its state (pulsate).

7 – keypad aux. alarm – the output starts on triggering the alarm by the user with the ALARM AUX

function. The output operation can be limited to the alarms from specified partitions. The output can

remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is

cleared by the user. During operation, it can every second change its state (pulsate).

8 – keypad tamper alarm – the output starts on detecting violation of the tamper contact or a change of

the keypad address, and also after 3 wrong codes. The output operation can be limited to the alarms

from specified partitions. The output can remain active for a specified time (from 01 to 99 seconds or

from 01 to 99 minutes) or until the alarm is cleared by the user. During operation, it can every second

change its state (pulsate).

9 – day/night + counting – the output starts on detecting violation of disarmed DAY/NIGHT zone or

violations of COUNTING zones, which trigger no alarm. Operation of the output can be restricted to

a specified “list of outputs” or particular partitions (identically as for the 1 output type). Indication of any

other zones than those tested by this output type is irrelevant – they will give no violation signal. The

output can remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until

the alarm is cleared by the user. During operation, it can every second change its state (pulsate).

10 – duress alarm – the output starts on using an access code with authority level 4 (DURESS) to disarm

the system or to signal an alarm. This code is used to trigger a special "disarm under duress" alarm.

Operation of the output can be restricted to alarms from particular partitions. The output can remain

active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is

cleared by the user. During operation, it can every second change its state (pulsate).

11 – chime – the output starts on violating the disarmed zones for which the “chime” option has been

activated. Operation of the output can be restricted to the indicated "list of zones" or to specified

partitions (identically as for the 1 output type). The output can remain active for a specified time (from

01 to 99 seconds or from 01 to 99 minutes) or until the alarm is cleared by the user. The output signals

violations irrespective of the chime lock setting in keypad (the lock is called by holding down the [8]

key).

12 – switch MONO – the output is activated by calling the user function 7 ([CODE][

][7]) or using a code

with authority level 5 ([CODE][#]). Operation of the output can be restricted to specified partitions.

The output can remain active for a time from 01 to 99 seconds or from 01 to 99 minutes.

Satel CA-10 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info