Bedienungsanleitung Satel CA-10 (Seite 6 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

4 Installer Manual SATEL

12 – arming – violation of this zone will arm the partitions the zone belongs to.

13 – silent arming – violation of this zone will arm in silent mode the partitions the zone belongs to.

14 – disarming – violation of this zone will disarm the partitions the zone belongs to.

15 – no alarm action – violation of this zone will activate the ZONE VIOLATION type outputs.

16 – arming/disarming – controls arming/disarming of partition to which this zone is assigned. Setting of

"PRIORITY" option allows to choose one of two different modes:

− PRIORITY option enabled: zone violation will arm the partition, while end of violation will disarm the

partition ("Bistable" action),

− PRIORITY option disabled: each violation of the zone will trigger partition's state between "Armed"

and "Disarmed" state ("Monostable" action).

17 – delay audible – a delayed zone with the delay countdown signaling in keypads.

18 – automatic bypass arming – violation of this zone arms the partition the zone belongs to,

simultaneously bypassing the zones programmed as AUTO-BYPASS (see FS16 – FS19).

19 – perimeter – zone armed since entering the access code and confirming it with the [#] key (i.e. arming

the partition). Violation of this zone during countdown of the „exit delay” will trigger an alarm.

20 – entry/exit-final – acts much like the type 0 (ENTRY/EXIT) zone, but the violated zone restore during

exit delay countdown will stop the countdown and begin the partition armed mode.

Reaction time for each zone can be programmed within 0.016 s to 4.08 s.

For each of the delayed zones, an individual time delay can be set.

Each zone involves a few options to determine the reaction in particular situations.

It is possible to determine for each zone the maximum violation time (in seconds), after which

the zone will be recognized by the control panel as defective, and to determine the maximum

"no violation" time (in hours), after which the zone will be recognized by the control panel as

defective.

The zones can be selectively bypassed.

For each zone can be determined the 9 event codes to be sent to the monitoring stations.

Outputs

The CA-10 is equipped with 6 programmable outputs: 4 high-current and 2 low-current ones.

The OUT1, OUT2, OUT3 and OUT4 outputs are protected by special electronic fuses with

current limiters set at 2.2 A. The panel monitors presence of voltage, overload, and signals

trouble conditions at these outputs. 2.2 kΩ resistors must be connected in parallel to these

outputs. The above outputs supply the load with +12 V voltage.

The OUT5, OUT6 outputs (low-current, up to 50 mA) control ground of the load.

All outputs are equipped with protective devices for inductive loads and pulse interference.

For each output can be defined the operation time in seconds (from 1 to 99 seconds),

in minutes (from 1 to 99 minutes), or LATCH type (until cut off). It is possible to determine the

output polarity for active state (+12 V or 0 V on the load), and whether it should operate in

pulsed or continuous mode.

Assignment of the particular outputs can be restricted to the specific partitions/zones of the

system.

Designation of the outputs can be adapted for the needs of the alarm system controlled by

the panel. Though individual outputs differ by their design, each of them can perform one of

the following functions:

0 – not used

1 – burglary alarm – the output starts on detecting a burglary alarm by the control panel. The alarm is

triggered by armed zones, zone tamper circuits, keypad tamper detectors, and by the user (through

the ALARM PANIC function). If the zones to which the output is to react are defined, the zone alarms

will be limited to those included in the „list of outputs” (the other alarms will be effected irrespective of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info