Bedienungsanleitung Satel CA-10 (Seite 35 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 33

Note: The names contained in the data of the first partition LCD keypad are used as

descriptions when scrolling through the event log.

In order to program the data you should:

• connect the RS-232 ports of keypad and computer with a corresponding cable (see:

DESCRIPTION OF CONTROL PANEL MAIN BOARD, point number 3 – RJ socket),

Note: For programming the LCD keypad a different cable is necessary than for

programming main board via RS-232 port. The cable for programming the LCD

keypad is available in the kit designated DB9F/RJ-KPL.

• start the DLOAD10 program in the computer and select the COM port to which the cable

is connected (see: Program configuration for...),

• open the file with alarm system data,

• open the LCD keypads window and select the corresponding keypad (tabs:

LCD 1...LCD 4),

• start the data readout by clicking on the Read field on the right-hand side of open window

(the correct readout operation is confirmed by the status bar indicator at the bottom of the

window),

• enter the data in the corresponding fields of the computer screen,

• save the data in the keypad memory by clicking on the Write field just below the Read

field,

• disconnect the cable from the keypad RS-232 port,

• repeat the programming operation for the other LCD keypads in the system.

REMOTE PROGRAMMING – DLOAD10

The DLOAD10 program delivered with the control panel is designed for programming the

CA-5, CA-6 and CA-10 panels, as well as the RX2K, RX4K radio controllers, GSM-4 and

GSM LT-1 module and ACU-100 wireless system controller from the computer. Additionally,

the program makes it possible to create documentation of alarm systems, sets of settings for

various configurations ("patterns" which facilitate the programming of new systems), event

sets for each system, as well as to remotely operate the control panel in the same way as

with the keypads.

The program is designed for IBM PC/AT compatible computers. It works in any computer

hardware configuration in the WINDOWS (9x/ME/2000/XP) environment. It is recommended

that the program be installed on the computer hard disk.

The control panel communicates with the computer through the RS-232 interface or via the

telephone line. For telephone communication with the panel, the program uses a modem

controlled by one of the COM ports (internal or external), compatible with the HAYES "AT

Command" standard. Communication with the control panel is possible in the CCITT V.21 or

BELL 103 standard (at 300 Bps). As the control panel transmits data only with a speed of

300 bauds, the modem must support this speed of operation.

Usually a suitable modem configuration is necessary – disabling the transmission

standard negotiating function and forcing the transmission speed of 300 Bps.

In order to install the program, run the D10setup.exe program from the CD, which is

delivered with the control panel. The installation completed, start the program. Access to the

program is protected with an access code. After installation, the code is 1234 and can be

changed to any sequence of 16 alphanumeric characters. As long as it has its factory form,

you can start the program (with default code 1234) by pressing the „ENTER” key (no access

code need to be entered).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info