Bedienungsanleitung Satel CA-10 (Seite 18 von 24) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

USER MANUAL CA-10

The text mode is signaled by

in the upper right corner of the display.

Numeric keys in text mode insert letters at the cursor position according to the

preceding table. Lowercase characters are entered by pressing a numeric key twice.

ST keys enable the previous/next character selection.

In numeric mode S key deletes the character before the cursor, and T key switches

between insert/typeover modes.

An access code can have the following functions/authority levels:

1 - accessible all functions, except creating and deleting users,

2 - accessible arming and disarming, change of access code,

3 - accessible arming, while disarming is only possible when the system was

armed with the same access code,

4 - code trap: it arms and disarms the system, but disarming sends a DURESS

("disarmed under duress") message to the monitoring station,

5 - activates the MONO SWITCH output, its use is recorded in the event log, can

serve as a guard code,

6 - changes the state of BI SWITCH output,

7 - partial arming - the code arms the system, simultaneously bypassing a group of

zones (specified by the installer in service functions), otherwise the code

provides the same features as that with authority level 2,

8 - accessible arming and disarming, without possibility to change own access

code,

9 - accessible arming only,

0 - accessible alarm clearing only.

Note: The codes with authority level 5 and 6 may be used in the following manner:

1. To control single outputs by means of the user functions:

− the code with authority level 5 enables the function 7 ([CODE][

][7]) i.e.

activates any output of the MONO switch type,

− the code with authority level 6 enables the function 8 ([CODE][*][8]) i.e. changes

the state of any output of the BI switch type.

2. To control all the outputs of a particular type, which belong to the partition where

the given code was created:

− the code with authority level 5 will activate the MONO switch type outputs

([CODE][#]),

− the code with authority level 6 will change the state of the BI switch type outputs

([CODE][#]).

EXAMPLE: enter the user code [3546] with authority level 2; master user code [1234]

[1234] [

] - call the "user function" mode; it should be acknowledged by one short beep

and blinking of the LEDs:

[

ALARM

], [

ARMED

[

TROUBLE

]

[2] - call the "User add" function, it should be acknowledged by two short beeps

[3546] [#] - enter the new code digits; their acceptance will be acknowledged by three

short beeps

[2] - assign authority to the code; the function will be quitted automatically which

will be confirmed by four short and one long beeps

User (code) erase [CODE][

][3]

This function is used for deleting the codes of existing users to revoke their right to use

the system. After entering the number of the user to be deleted, the panel waits for

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info