Bedienungsanleitung Satel CA-10 (Seite 20 von 24) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

USER MANUAL CA-10

Silent arming [CODE][

][5]

In the silent armed mode the alarms are only signaled in keypads and reported to the

monitoring station. The installer decides if the silent armed mode is to be active in the

entire protected facility or if a selected area will remain disarmed.

The function is not available to the users with authority levels 5, 6, 0.

Time setting [CODE][

][6]

The function enables setting the panel’s clock.

In the LED keypad the programming procedure is as follows:

- HOURS, MINUTES - acceptance ([H][H][M][M][#]),

- DAY, MONTH - acceptance ([D][D][M][M][#]),

- YEAR - acceptance ([R][R][R][R][#]).

It is possible to quit the function already after programming either time or date by

pressing the [#] key twice.

In the LCD keypad the programmable parameters (time, data, year) can be edited with

additional keys: ◄ and ► keys position the cursor, ▲ key deletes the character before

the cursor, ▼ key switches data entry mode (insert/type over).

The function is only available to the master user and users with authority level 1.

MONO switch outputs activate [CODE][

][7]

The purpose of the function will be determined by the installer. It can activate e.g.

electric locks, bells, signal lamps, or any other devices.

After calling the function, the control panel generates two short beeps and waits for the

output number key (1-6) to be pressed. The control consists in activating the given

output for a period of time programmed in the control panel. Provision is made for

multiple control of the same output or control of different outputs of the MONO switch

type after single calling of the function. Correct performance of the control is confirmed

by four short and one long beeps, and refusal of the control - by two long beeps. The

control panel may refuse control, if the output is not of the SWITCH MONO type or if it

belongs to another partition. Pressing the key [#] or [

] will end the function. The control

panel will automatically end the function if none of the outputs is of the SWITCH MONO

type, or if no key on the keypad is depressed for 40 seconds.

The function is accessible to the master user, as well as to the users with authority

levels 1 and 5.

EXAMPLE: successive control of the outputs 4, 5, 4 (master code=1234)

[1234] [

] - calling the "user function" mode by the MASTER user

[7] - calling the function of "MONO switch outputs activate" (two short beeps)

[4] - monostable triggering of the output 4 confirmed by four short and one long

beeps

[5] - monostable triggering of the output 5 confirmed by four short and one long

beeps

[4] - monostable retriggering of the output 4 (four short and one long beeps)

[#] - end of the function (four short and one long beeps)

BI switch outputs activate [CODE][

][8]

The purpose of the function will be determined by the installer. It can be used e.g. for

switching on external lighting or any electrical equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info