Bedienungsanleitung Satel CA-6 (Seite 8 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

6 SATEL Installer Manual

special "disarm under duress" alarm. Operation of the output can be restricted to alarms

from particular partition. The output can remain active for a specified time (from 01 to 99

seconds or from 01 to 99 minutes) or until the alarm is cleared by the user. During

operation, it can every second change its state (pulsate).

11 – chime – the output starts on violating the disarmed zones for which the “chime” option has

been activated. Operation of the output can be restricted to the selected "list of zones" or

to specified partition (identically as for the 01 output type). The output can remain active

for a specified time (from 01 to 99 seconds or from 01 to 99 minutes). If the LATCH option

(on until switch-off) is enabled for the output, it will be deactivated when the alarm is

cleared by the user. The output signals violations irrespective of whether the chime blocking

in the keypad is on or off (to enable the blocking, press and hold down the key [8]).

12 – switch MONO – the output is activated by calling the user function 7 ([CODE][

][7]) or using

a code with authority level 5 ([CODE][#]). Operation of the output can be restricted to

specified partition. The output can remain active for a time from 01 to 99 seconds or from

01 to 99 minutes (do not program the LATCH option for the output).

13 – switch BI (ON/OFF) – the output changes its state when the user function 8 ([CODE][

][8]) is

called or a code with authority level 6 ([CODE][#]) is used. Operation of the output can be

restricted to specified partition.

14 – arm status – the output is active in the armed mode. Operation of the output can be restricted

by selecting a "list of zones" or partition. Unless zones and partitions are selected, the

output is active when any partition (zone) is armed.

15 – silent arm status – the output is active in the silent armed mode. Operation of the output can

be restricted by selecting a "list of zones" or specific partitions.

16 – exit delay status – the output is active during the "exit delay" countdown by the control panel.

Operation of the output can be limited to indicating the "exit delay" for specified partition.

17 – entry delay status – the output is active during the "entry delay" countdown. Operation of the

output can be limited to selecting the "entry delay" for specified partition.

18 – telephone usage status – the output is active when the control panel is on the telephone line.

19 – ground start – the output is activated by the control panel if the GROUND START signal is to

be generate (a 2 sec. signal occurring before the control panel "lifts the handset" required

by a specific type of telephone exchanges).

20 – monitoring confirmation – the output activated for 3 seconds by the control panel, after

correct termination of the monitoring session.

21 – bypass status – the output is active when some zones are bypassed in the system. Operation

of the output can be limited to showing the bypass of zones specified in the list of zones,

or the bypass of selected partition zones.

22 – READY status – the output is active when all the control panel zones are free from violations.

Operation of the output can be limited to showing the READY status of zones specified in

the list of zones, or the READY status of selected partition.

23 – zone violation – the output starts when one of the zones is violated. Operation of the output

can be limited to the selected "list of zones" or specified partition (identically as for the 01

output type). The output can remain active for a specified time (from 01 to 99 seconds or

from 01 to 99 minutes) or until the armed mode is deactivated or the alarm cleared.

24 – telephone line trouble – the output used when telephone messaging is doubled by radio

messaging; it makes possible reporting the telephone line trouble.

25 – AC power loss.

26 – battery trouble – activated when the battery voltage in three consecutive tests drops to about

11 V.

27 – power supply – the output intended for powering detectors, radio lines and other equipment

with 12 V direct voltage. When programming this type of output, pay special attention to

permissible current-carrying capacity of each of the control panel outputs.

28 – fire detectors power supply – the output intended for powering the fire detectors.

The output closely interacts with the “24H fire” zones. If assigned to any of the control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info