Bedienungsanleitung Satel CA-6 (Seite 9 von 36) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CA-6 SATEL 7

panel outputs, it activates the fire alarm verification function. The verification operates as

follows: the first violation cuts the fire detectors power supply off for about 15 seconds.

The power-down results in reset of the violated detectors. Then, the power supply is

restored, but the panel will not control the “24H fire” zones for ten to twenty seconds

because of the balancing of detectors. Next, the control panel enters the special mode of

fire detectors control, which lasts about 90 seconds. If a repeated detector violation occurs

during that time, a FIRE alarm will be triggered. Otherwise, the control panel will go over

to the normal control of “24H fire” zones (duration of the whole verification process is

approx. 2 min.). The output reacts to the "RESET power supply" function (user function 9).

29 – power supply with RESET function – the output is designated to power detectors which

require a periodical power cut-off until the state memory is cleared. The RESET function is

activated from keypad through the user function 9 (calling: [CODE][

][9]). The voltage is

cut off for time programmed as the output active time.

30 – TIMER – the output is controlled by the control panel clock; it is activated/deactivated in the

hours indicated by a corresponding TIMER (see: Functions programming TIMERS).

31 – audible alarm status – the output signals the audible armed mode. Operation of the output

can be limited to the selected "list of zones" or partition.

32 – full arm status – the output is only active when all zones/partitions assigned to it are in the

armed mode.

33 – ARM/DISARM/CLEAR ALARM – the output signals the particular system states with,

respectively, one, two, or four pulses 0.16 s each.

34 – alarm in keypad – silent alarm signaling in the partition keypad.

35 – power supply on armed mode – it functions similarly to the ARM STATUS output, but it is

activated right after "exit delay" starts, not after changeover from the exit delay to the

armed mode (it can be used, for example, as indicator or power supply output for

microwave detectors in spaces where people stay).

36 – signalling: LED – the output can control a LED to indicate the following statuses:

- off – control panel disarmed

- steady light – control panel armed

- blinking light – the control panel armed, there was alarm or trouble

Note: If in the armed mode any zones are violated in the system, the LED will be

blinking and will only change to steady light after the violation ends.

37 – signalling: relay – the output can control a relay. The output becomes active after arming,

and inactive after an alarm is triggered, a trouble occurs, or the system is disarmed.

Note: If in the armed mode any zones are violated in the system, the output will

become active after the violation ends.

38 – not used – (do not program).

39 – no guard code – the output is activated by a timer programmed as the partition control

TIMER, unless a guard code is entered within the timer specified time.

40 – service mode status – the output is activated if the control panel service mode has been

called from any keypad.

41 – battery low status – the output, which state is updated after each battery voltage test.

Partitions

A new partition is created when at least one zone is assigned to it. The CA-6 permits creating

of two partitions to which any outputs, telephone numbers and pager messages can be

assigned, and thus enables two alarm systems to be built on the basis of one CA-6 control

panel. The partitions can be controlled from a keypad (access codes assigned to the

partitions) as well as by means of control zones. Both partitions can be controlled at the

same time.

Because the sirens connected to the outputs can be activated by selected zones, the

assignment of zones to partitions will define which codes can clear alarm on particular sirens.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info