Bedienungsanleitung Satel CA-6 (Seite 24 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

22 Programming CA-6

Note: Assignment of events is necessary for the mode of reporting to both stations with

event assignment. The unassigned events will not be sent, despite the properly

programmed codes.

Monitoring - programming partition event codes

FS69 - programming A partition event codes (HEX)

FS70 - programming B partition event codes (HEX)

The partition event codes can be single- or double-character. For the data formats 4/1 and

3/1, one of the characters must be equal to 0, and the mode of extension by the user

number should be deactivated (see FS47 "Monitoring options ").

When the event codes are to be double-character ones, the panel can extend some codes

with the user number. In case of codes, which are to be extended, one of the characters

should be programmed as 0. Additionally, the mode of extension by the user number

should be activated. The code of event caused by the MASTER user is extended by "F",

the codes of other users – by "1"..."C".

Where the partition is controlled by zones, the event code is extended by "D". When the

event is caused by the clock (see: the "Functions programming TIMERS"), the event code

is extended by "E". Programming the 00 setting means that we cancel sending event

information to the station.

The programming consists in assigning two characters (from 1 to F, 0 means no digit) to

each partition event and confirming them. When programming, the 1 to 8 keypad LEDs

show the programmed code (1 to 4 the first character, 5 to 8 the second character of the

code). The AB, AB LEDs show the number of event programmed, according to the list

below:

Number AB, AB diode state Event

1  Arming *

2  Disarming *

3  Zone bypass *

4  DURESS alarm

5  Silent arming

6  Arming with bypass

7  Partial arming

8  quick arming

9  Clearing alarm

Notes:

• The codes, which can be extended by the user number, are marked with *.

• The “Silent arming” code is sent in addition to the “Arming” code, which is sent with the

user number.

• The “Arming with bypass” code is sent if some of the partition zones are bypassed at

the moment of arming.

• The “Partial arming” code is sent in addition to the “Arming” code when in a system

with two partitions one partition is armed and the other is disarmed.

See also: function FS126 (programming the guard control codes).

FS73 - programming A partition event assignment to station 1 (BIT)

FS74 - programming B partition event assignment to station 1 (BIT)

The functions FS73 and FS74 define which events from a given partition will be reported to

the first monitoring station when the mode of reporting to both stations is activated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info