Bedienungsanleitung Satel CA-6 (Seite 22 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

20 Programming CA-6

Monitoring - programming identifiers

FS48 - programming event identifier for station 1 (HEX)

FS54 - programming event identifier for station 2 (HEX)

The functions FS48 (station 1) and FS54 (station 2) are used to program the identifiers

transmitted to the monitoring stations. Programming is carried out in the manner typical for

hexadecimal functions (HEX); the LEDs 1 to 8 shows two consecutive characters, which

can be changed by entering new ones. When the first two characters are being

programmed, the lower B LED blinks, and when the other two - the lower A LED.

For the data formats 3/1 and 3/2, the last character should be 0 - the control panel will

send characters from 1 to F, 0 not being sent.

Note: If the monitoring station requires an identifier containing the digit zero, enter the

character “A” instead of zero (e.g. the identifier “1203” should be entered as

“12A3”).

EXAMPLE:

programming the identifier for the station 1 = A243

[12345] [#] - enter the service mode

[4][8] [#] - call the function

[

0][2] [#] - enter the first two characters of identifier (B LED blinking)

[4][3] [#] - enter the next two characters of identifier (A LED blinking) and confirm them - exit the

function

Monitoring - programming zone event codes

The zone event codes are programmed in the functions FS60, FS61 and from FS63 to

FS65. Each of them is used for programming a code of one event for each of the eight

zones.

The zone event codes may be either single or double character. If a single-character code

is entered (for the data formats 4/1 and 3/1 and also when using the mode with code

extension by zone number, see FS47 "Monitoring options"), one of the characters must

be 0. Programming 00 will result in skipping the event when the events are being

reported to the station.

The programming consists in entering two characters (from 0 to F) for each zone and

confirming them. During the programming, the keypad LEDs show value of the character

entered (from 1 to 4 - the first character, and from 5 to 8 - the second character of the

code) and number of the zone for which the code is programmed (AB, AB LEDs). After the

last zone code is confirmed, the control panel exits the function .

FS60 - programming zone alarm codes (HEX)

The codes programmed with this function are reported when the control panel detects

zone violation, which triggers an alarm.

Codes of 8 control panel zones are programmed in turn.

EXAMPLE:

programming the alarm codes for the zones 1 to 7 (codes from 41 to 47), the zone 8 is

not an alarm one.

[12345] [#] - enter the service mode

[6][0] [#] - call the function

[4][1] [#] - program the code for zone 1

[4][2] [#] - program the code for zone 2

[4][3] [#] - program the code for zone 3

[4][4] [#] - program the code for zone 4

[4][5] [#] - program the code for zone 5

[4][6] [#] - program the code for zone 6

[4][7] [#] - program the code for zone 7

[0][0] [#] - program the code for zone 8 (no event for zone 8), exit the function

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info