Bedienungsanleitung Satel CA-6 (Seite 21 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 19

• In the 0E format (Contact ID selected codes) monitored are all events which have a CID

code and which are assigned, respectively, to the station 1 or 2 in the corresponding

event assignment functions of the control panel, while the events which have no

assignment function (marked in the „Appendix” table as no assignment) are only

monitored when any non-zero monitoring code has been programmed for them.

• The telephone line restore and trouble events are always monitored in both Contact ID

formats, while they are not monitored in the other formats.

FS47 - programming monitoring options (BIT)

These options determine the way communication is established with the monitoring

stations and how the event codes are transmitted. The programming consists in lighting up

the LEDs of selected options and confirming the choice with the [#] key.

No. LED Option

1 OFF

2 OFF

transmission to station 1 or station 2 (report is sent to the one station only, to

that, which first answers the call, without event sorting)

1 ON

2 OFF

report to station 1 only, without event sorting

OFF

2 ON

report to station 2 only, without event sorting

2 ON

transmission to both stations with event sorting (event sorting programmed

with corresponding service functions, separately for each group of events)

reported partition event code extended with user number (access code

number)

OFF

automatic extension with user number disabled

reported zone event code extended with zone number (for zone 1 - "1", for

zone 2 - "2" and so on)

OFF

extension with the zone number disabled

panel does not send the event code if STATION 1 fails to acknowledge receiving

the information after 16 attempts

OFF

the panel skips no codes for STATION 1

the panel skips sending the events code if STATION 2 fails to acknowledge

receiving the information after 16 attempts

OFF

the panel skips no codes for STATION 2

Notes:

• In case of data formats 4/1 and 3/1, do not enable the options 5 and 6.

• The options 5 and 6 are only meaningful when double-character codes are reported. If

this is the case, single-character event codes are programmed (the second character

being 0), and the panel, with the extension option on, will add the zone number or the

user number, respectively, as the second character. The codes programmed as

double-character (both characters different from 0) will be sent in their programmed

form, with no extension. Extension of the event codes by adding the zone / user

number makes it possible to enter identical codes for one type of events for all zones

or partitions, and then to differentiate between them, based on the added zone / user

no. (e.g., it is sufficient to program just one, identical character for all zones from which

the zone alarm code (FS60) is to be sent). This solution has been adopted to facilitate

programming of the event codes.

• The options 3 and 4 are not used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info