Bedienungsanleitung Satel CA-6 (Seite 19 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 17

operation time in minutes

OFF

operation time in seconds

LATCH type output – signaling until cleared (operation time irrelevant)

OFF

programmable output operation time

polarity +12V when the output is active

OFF

polarity 0V when the output is active

Note: The option of output assignment to the partition is to be used, when separate

sirens have to be assigned to individual partitions. If not assigned to a partition,

the alarm output will signal every alarm.

EXAMPLE:

programming the OUT1 output as the BURGLARY/FIRE ALARM type with 5 minutes

operation time and polarity 0V in active state

[12345] [#] - enter the service mode

[3][1] [#] - call the function. The LEDs 1-8 shows number of current output type (LEDs 1-4 shows

binary first digit, LEDs 5-8 – second digit). The blinking B LED signals the output type

being programmed

[0][2] [#] - enter and confirm the number of output function (the A LED starts blinking - operation

time programming)

[0][5] [#] - program and confirm the time (A and B LEDs start blinking - output option programming)

[6] - LED 6 goes on - the „time in minutes” option is activated

[8] [#] - LED 8 goes off - set the "polarity" = 0V and exit the function

Note: Choosing a partition in the options will determine which access code is to be

used to switch off siren or to control a zone. The same effect is provided by

defining a list of zones controlling the outputs.

FS32 - programming list of zones for OUT1 (BIT)

The function is used to program the output controlling zones. The selection of zones limits

the output operation only to the reaction to violation of those particular zones.

The zone selection should only be used when it is necessary to have separate

signaling for events from a specific zone or a group of zones. If no list of zones is

programmed, the control panel will assume by default that the output reacts to events from

any zone – for example, the BURGLARY alarm type output will signal alarms for each

control panel alarm zone. Of course, the zone function (reaction type) is taken into

consideration, e.g. the alarm signaling output does not react if the state of the arming zone

changes.

If the list of zones has been programmed the control panel will skip the programmed

selection of partitions.

The FS32 function is used to assign zones to the OUT1 output. The programming consists

in lighting up the LEDs which correspond to the zones. When the list is completed, it

should be confirmed.

FS33 - programming OUT2 output

The function allows for defining the basic parameters associated with the OUT2 output.

The programming procedure is the same as for the FS31.

FS34 - programming list of zones for OUT2 (BIT)

The function programs the list of zones associated with the OUT2 output. The

programming procedure is the same as for the FS32.

FS35 - programming OUT3 output

The function defines the basic parameters associated with the OUT3 output. The

programming procedure is the same as for the FS31.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info