699578
17
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
CA-6 SATEL 15
ON
zone violation end code will be reported to the monitoring station not immediately but
only after the zone is disarmed (RESTORE AFTER DISARM)
8
OFF
zone violation end code will be reported to the monitoring station immediately (if
option 7 is off)
During programming, the AB, AB LEDs show the zone number for which the options are
being programmed.
Note: By default, the option no. 1 is active for all of the zones, which means that
arming
is impossible, if any of the zones is violated or tampered
.
FS28 - programming individual entry delay (DEC)
Where different entry delay times are required for the particular zones, it is possible to
program individual "entry delay time" (alarm delay). The programming consists in entering
the time for delayed zones from 00 (then the global time specified in FS6 is valid) to 99
seconds. The programmed times refer only to the ENTRY/EXIT, DELAYED, INTERIOR
DELAYED and 24h AUDIBLE zone types. If the entry delay is programmed for other zones
than the delayed ones (e.g., for the INSTANT zones), it will have no effect on the reaction
type of those zones.
EXAMPLE:
programming the entry delay time (alarm delay) for the following zones: zone 4 - delay
30s, zone 7 - delay 45s, zone 8 - delay 60s.
12345] [#] - enter the service mode
[2][8] [#] - call the function
[#] - skip programming entry delay for zone 1
[#] - skip programming entry delay for zone 2
[#] - skip programming entry delay for zone 3
[3][0] [#] - program the entry delay for zone 4
[#] - skip programming entry delay for zone 5
[#] - skip programming entry delay for zone 6
[4][5] [#] - program the entry delay for zone 7
[6][0] [#] - program the entry delay for zone 8
[
*
] - exit the function
Functions programming output parameters
FS31 - programming OUT1 output
The function makes it possible to define three parameters regarding the OUT1 output:
After selecting the function, the LEDs 1 to 8 show the respective parameter setting, while
the LEDs A,B show which parameter is being programmed.
Output function (B diode is blinking) - the programming consists in entering a two-digit
number (identically as in the DEC functions) and confirming it with the [#] key, which is
followed by an automatic jump to next parameter programming. It is possible to program
one of the functions below for each zone, and thus specifying situations when the output
will be activated:
00 - NOT USED
01 - BURGLARY
02 - FIRE/BURGLARY
03 - FIRE
04 - KEYPAD ALARM
05 - FIRE FROM KEYPAD
06 - PANIC FROM KEYPAD
07 - MEDICAL (AUX) FROM KEYPAD
08 - TAMPERING (KEYPAD/MODULE)
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Satel CA-6 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Satel CA-6

Satel CA-6 Zusatzinformation - Deutsch - 19 seiten

Satel CA-6 Bedienungsanleitung - Deutsch - 19 seiten

Satel CA-6 Installationsanweisung - Deutsch - 80 seiten

Satel CA-6 Bedienungsanleitung - Deutsch - 18 seiten

Satel CA-6 Kurzanleitung - Englisch - 8 seiten

Satel CA-6 Installationsanweisung - Englisch - 36 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info