Bedienungsanleitung Satel CA-6 (Seite 23 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 21

FS61 - programming zone tamper alarm codes (HEX)

The codes programmed with this function are reported when the CA-6 detects violation of

the tamper contact in 2EOL/NC and 2EOL/NO line, which triggers a tamper alarm.

FS63 - programming zone violation codes (HEX)

The function is used for programming the zone violation codes. The zone violation code is

transmitted to the monitoring station in case of:

• violation of an armed delayed zone (of entry/exit, interior delayed, delayed type)

when the control panel has started the entry delay countdown,

• violation of an armed counting zone when the number of violations still does not

trigger an alarm,

• violation of a day/night zone when it is disarmed,

• violation of an armed zone when the zone already signals an alarm - during the

alarm no subsequent alarms are signaled, and the consecutive detector activation is

recorded in the event log as “zone violation”; when the alarm signaling is over, each

next violation of the detector will trigger an alarm.

Note: If the alarms and violation codes are not program for all zones than the station

may not be notified of the alarm. If one of the control panel zones has no alarm

code assigned to it, and it will trigger an alarm, the activation of subsequent

detectors, which occur during the alarm, will be saved in the memory as zone

violation, not as alarm. If the system comprises any zones triggering an alarm of

which the monitoring station is not notified, it is necessary to enter the same

violation codes as for the alarms.

FS64 - programming zone RESTORE (end of violation) codes (HEX)

The codes programmed with this function are sent after the zone returns to its normal state

(according to the setting of corresponding zone options).

FS65 - programming zone TAMPER RESTORE codes (HEX)

The codes programmed with this function are sent after the tamper contact of the detector

connected to the 2EOL/NC and 2EOL/NO zones returns to its normal state.

FS67 - programming zone event assignment to station 1 (BIT)

FS68 - programming zone event assignment to station 2 (BIT)

The functions indicate which zone events are to be sent to station 1, and which to

station 2, if transmission to both stations has been selected in function FS47. The

programming consists in lighting up the LEDs to indicate the events (as per the list below)

and confirming the selection with the [#] key.

No. LED Option

send „zone alarm” code

OFF

do not send „zone alarm” code

send „zone tamper alarm" code

OFF

do not send „zone tamper alarm" code

send „zone violation” code

OFF

do not send „zone violation” code

send „zone restore” code

OFF

do not send „zone restore” code

send „zone tamper restore” code

OFF

do not send „zone tamper restore” code

The state of LEDs 3, 7 and 8 is irrelevant.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info