Bedienungsanleitung Satel CA-6 (Seite 33 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 31

Start programming through RS-232

The function starts the mode of control panel programming through the RS-232 interface.

Prior to calling the function:

• connect the control panel to the computer with the special cable (see: I

NSTALLER

ANUAL

, chapter: D

ESCRIPTION OF

ONTROL

ANEL

AIN

OARD

description

of the

RJ socket);

• start the DLOAD10 program in the computer and select the number of communication

port (COM);

• open the menu „Communication” and select the „RS-232” item, and then „Local

connection with…” (select the CA-6 control panel);

• select the service mode in the control panel and start the FS112 function.

If the control panel receives no dial tone from the computer within 10 seconds (wrong

computer connection cable or port number), the function will quit automatically.

Programming with the use of modem

Before calling the function:

• connect the modem to the control panel;

• start the DLOAD10 program in the computer and select the number of communication

port (COM);

• open the menu File, item

→

„Open...” or

→

„New”, and select the control panel

→„

CA-6"; open

the menu Communication and select

→

„Modem"; and, in the „Modem initialization” window,

select

→

„Local connection with” – the computer will ask you to call the FS112 function.

The control panel can also be programmed without calling Function FS112 in the

keypad (see: Installer Manual).

After calling the FS112 function (just as in case of the other service functions) the

[

TROUBLE

]. LED is on and the control panel tries to establish communication with the

computer. If it fails within about 20 seconds, the panel exits the function signaling an error

(two long beeps). When the communication is established (four short and one long beeps),

the control panel exits the function to the service mode.

The online communication is maintained until a corresponding command is received from

the computer.

More information is given in the Installer Manual.

FS117 - telephone line trouble delay (DEC)

The function defines how many minutes may elapse from the low voltage condition on the

telephone line to the moment the panel reports a trouble. Lifting the handset of

a telephone connected to the same telephone line is also recognized as a telephone line

loss. The programming consists in entering a two-digit number from 00 to 99 minutes. If 00

is programmed, the panel never reports the telephone line voltage trouble.

EXAMPLE:

programming a twenty-minute delay

[12345] [#] - enter the service mode

[1][1][7] [#] - call the function

[2][0] [#] - program the delay

FS118 - parameters of pager station signals (HEX)

The function defines parameters of the answer signals generated by automatic pager

station. As different answer signals are used in each system, it is necessary to specify the

signal parameters of the system to which the panel transmits its messages. If parameters

of such signals change, it will be sufficient to specify new data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info