Bedienungsanleitung Satel CA-6 (Seite 34 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

32 Programming CA-6

The programming consists in entering six two-character codes which are suitable for the

given paging system.

The particular systems should be programmed as follows:

• POLPAGER - [118]# [3B]#[42]#[0B]#[0F]#[01]#[7D]#

• TELEPAGE - [118]# [2B]#[2E]#[0E]#[14]#[30]#[3A]#

• EASYCALL - [118]# [37]#[3D]#[07]#[0B]#[B6]#[C8]#

• METROBEEP - [118]# [16]#[1A]#[13]#[17]#[0B]#[0F]#

FS123 - counter count-up times (DEC)

The function makes it possible to program time intervals related to the counters 1, 2 and 3

of counting zones. The alarm will be generated only if the number of violations preset in

FS7 function takes place within the time interval defined by this function. The count-up

times may be programmed within the interval from 1 to 255 seconds (by default set at 30

seconds). If the number of violations programmed in the FS7function does not take place

within the time interval defined in the function, after expiry of the time the counting zones

counters will be reset.

After starting the function, you should enter one, two or three digits for the first counter.

Upon confirmation with the key [#], the control panel proceeds to programming the count-

up time of the next counter. In the course of programming, the AB, AB LEDs indicate (in

binary format) the counter number. On the LEDs 1-8, the control panel displays the

previously programmed setting of the parameter in the binary format (the introduced

changes will be only displayed after the function is reentered). The programming can be

terminated by pressing the [

] key.

EXAMPLE:

changing the counter count-up time: the first one – 60 seconds, the second – 150

seconds, the third – 255 seconds,

[12345] [#] - enter the service mode

[1][2][3] [#] - call the function

[6][0] - enter the first counter time (B LED is blinking during programming)

[#] - confirm the counter 1 count-up time and proceed to programming counter 2

[1][5][0] - enter the second counter time (A LED is blinking during programming)

[#] - confirm the counter 2 count-up time and proceed to programming counter 3

[2][5][5] - enter the third counter time (A & B LEDs are blinking during programming)

[#] - confirm the counter 3 count-up time and quit the function

FS124 - automatic readout of keypad address

The function enables the keypad address to be automatically read without changing the

other parameters.

FS125 - programming CTL input functions (HEX)

The CTL control input of the CA-6 panel can perform one of the following functions:

0 – not used,

1 - arming,

2 - disarming,

3 - FIRE alarm,

4 - PANIC alarm,

5 - alarm AUX,

6 - arming / disarming,

7 - alarm cancelling (no disarming).

Two digits are programmed. The first of them defines the input function (from 1 to 7), the

second defines which partition should be armed, disarmed or in which partition should be

cleared an alarm.

0 - for functions: FIRE alarm, PANIC alarm, alarm AUX,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info