Bedienungsanleitung Satel CA-6 (Seite 35 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 33

1 - arming / disarming or cancelling alarm – A partition,

2 - arming / disarming or cancelling alarm – B partition,

3 - arming / disarming or cancelling alarm – A & B partition.

Note: Do not program any values beyond the permissible.

The input responds to shorting to ground (approx. 0.5 sec.). For example, if function 6

(Arm/Disarm) has been programmed, the partition will be armed on shorting to common

ground, and disarmed on breaking the ground connection and shorting to ground again

The input violation generates the following event codes:

• for input functions 3,4 or 5 - codes of keypad alarms programmed with function FS82,

• for the other functions - codes of arming or disarming (alarm clearing) by the input with

„D” extension (programmed with functions FS69 and FS70).

FS126 - programming guard control codes (HEX)

Four event codes are programmed in the following order:

• entry/exit A partition (enter control code – A partition) – the lower B LED is blinking,

• entry/exit B partition (enter control code – B partition) – the lower A LED is blinking,

• no control code in A partition – the A and B diodes are blinking,

• no control code in B partition – the upper B diode is blinking.

The programming of the partition control codes is similar to the programming of the FS69

and FS70 functions. If the "entry/exit" codes are one-digit numbers and the respective

option is on (see: FS47), they can be automatically extended by the user number.

FS127 - zones bypassed on no exit from A partition (BIT)

FS128 - zones bypassed on no exit from B partition (BIT)

The EXIT-BYPASS service functions 127 and 128 make it possible to program for each

partition the zones which will be automatically bypassed if, after arming, there is no

violation of the ENTRY/EXIT type zone during the exit delay (after arming the system, the

user has not left the site and has not violated any detector in the ENTRY/EXIT type zone.

The programming is similar to the programming of the FS16 and FS17 functions.

FS131 - programming additional options (BIT)

FIRST SET OF THE OPTIONS (the lower B diode is blinking)

No. LED Option

hardware entering service mode blocked

OFF

hardware entering service mode enabled

hardware start of downloading disabled

OFF

hardware start of downloading enabled

pulse dialing ration 1:1,5

OFF

pulse dialing ration

1:2

remote control module (MST-1) supported

OFF

remote control module (MST-1) not supported

Option 1 refers to disabling the hardware access to the service mode. If this option is

selected, it is only possible to enter the service mode by using the service access code.

The procedure of entering the service mode when the service code has been lost and the

possibility of starting the service mode by hardware means (jumpers) is disabled is

described in the Installer manual, in section: Entering service mode “from pins”. Carrying

out the procedure will result in the loss of all settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info