Bedienungsanleitung Satel Integra 64 (Seite 79 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 77

7. GSM phone only INTEGRA 128-WRL

You can program the GSM phone settings in the INTEGRA 128-WRL control panel:

• using the keypad, in the service mode, by means of the functions available in the GSM

submenu (STRUCTURE HARDWARE GSM),

• using the DLOADX program, in the “Structure” window, “Hardware” tab, after clicking on

the “GSM phone”.

7.1 GSM phone parameters and options

Shown in the square brackets are the names, as used in the keypads.

GSM phone [Use GSM phone] – when the option is enabled, the control panel supports the

GSM communicator. The option may be disabled if the GSM communicator is not to be

used (e.g. SIM card is not installed, etc.). Disabling the option will thus prevent any GSM

related troubles from being unnecessarily reported.

PIN [PIN code] – PIN code of the SIM card.

If the PIN code of SIM card is inconsistent with that entered in the control panel

settings, the control panel will inform of it by means of a suitable message and an

audible signal in the LCD keypad. After 255 seconds the control panel will retry to use

the PIN code. If the PIN code is wrong, the control panel will signal it again. After the

third attempt to use a wrong PIN code, the card will be blocked. In such a case, the

PUK code will have to be entered.

PUK code – the parameter available in the keypad only (STRUCTURE HARDWARE GSM

PUK CODE), when as a result of entering invalid PIN code the SIM card has been

blocked. After entering a correct PUK code, confirmed by pressing the key, the SIM card

will by unblocked, receiving a new PIN code.

Modem format – transmission standard suitable for the modem with which the GSM module

communicates.

SMS center no. – telephone number of the short message service center. Entering the

number is necessary if the GSM communicator is to send SMS messages. The number

entered in the control panel must correspond to the network in which the GSM

communicator is used (this depends on the SIM card installed in the control panel).

GSM band – selection of the frequency bands which are to be supported by the GSM phone.

The function is available for the electronics board version 2.1 or newer. If no band is

selected, the phone will support all bands.

GSM auto-restart after [Autorestart[h]] – idle time of the GSM phone after which it is

restarted. To be defined in hours.

GPRS

GPRS APN – access point name for Internet GPRS connection.

Username [User] – user name for Internet GPRS connection.

Password [Passwd] – password for Internet GPRS connection.

DNS server – IP address of DNS server to be used by the control panel. It is necessary for

GPRS communication, when the address of device to which the control panel is to connect

(computer with DLOADX or GUARDX program, monitoring station) has been entered in

the form of a name. If all addresses are entered in the form of an IP address (4 decimal

numbers, separated by dots), the DNS server address need not be programmed.

The GPRS parameters can be obtained from the GSM network operator.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info