Bedienungsanleitung Satel MICRA (Seite 43 von 52) (Englisch)

699548

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

SATEL MICRA 41

5. When the SIA-IP format is selected:

– define the account number to be used to identify the control panel for the reporting

purposes (“SIA-IP account no.” field);

– define the time interval at which an additional test transmission is to be sent (“Test

transm. every” field).

6. Indicate the monitoring station to which the event code is to be sent (the event may be

sent to both stations) and define the Contact ID codes for events to be reported. It should

be done in the “Reporting” tab, the “Keyfobs” tab (“Reporting” tab) and in the “MKP-300

keypad” tab, “Messaging / reporting” table. In the alarm module mode, with the “Set CID

codes automatically” option enabled, the codes are assigned automatically.

4.7 STARTING SMS REPORTING

1. Enter the telephone number of Short Message Service Center in “SMS center number”

field in the “GSM telephone, Monitoring stations” tab”, unless it has been saved by the

operator to the SIM card memory.

2. Configure parameters of the monitoring station(s) (“GSM telephone, Monitoring stations”

tab):

– select the “SMS” field;

– enter the GSM telephone number through which the monitoring station receives SMS

messages (“Tel. number (SMS)” field).

3. Define the SMS message format in which the received event codes will be sent to the

monitoring station (“GSM telephone, Monitoring stations” tab).

4. Indicate the monitoring station to which the event code is to be sent (the event may be

sent to both monitoring stations) and define the Contact ID codes or two-character codes

for events to be reported. It should be done in the “Reporting” tab and the “Keyfobs” tab

(“Reporting” tab) and in the “MKP-300 keypad” tab, “Messaging / reporting” table. In the

alarm module mode, with the “Set CID codes automatically” option enabled, the codes are

assigned automatically.

4.8 STARTING CLIP / SMS MESSAGING

The SMS or CLIP messaging is conducted irrespective of the monitoring.

1. Enter the telephone number of Short Message Service Center in “SMS center number”

field in the “GSM telephone, Monitoring stations” tab”, unless it has been saved by the

operator to the SIM card memory.

2. Enter the telephone numbers which are to be notified by the module, using the SMS

messages or CLIP service (“Telephone numbers for messaging and test transmissions”

table in the “GSM telephone, Monitoring stations” tab).

3. Define about which events and in what form (CLIP or SMS) the predefined telephone

numbers are to be notified. In case of SMS messaging, it is necessary to define the

content of SMS message. It should be done in the “CLIP / SMS messaging” tab and the

“Keyfobs” tab (“CLIP / SMS messaging” tab) and in the “MKP-300 keypad” tab,

“Messaging / reporting” table. For events related to the analog zones, you can additionally

enable the “Add input voltage value to message” option.

4.9 CHANGING THE TEXT MESSAGES BY USING SMS

The content of SMS message defined:

– in the “Violation / pass” and “Restore” fields, “CLIP/SMS messaging” tab,

– in the “SMS” field, “Keyfobs” tab,

– in the “SMS” field, “MKP-300 keypad” tab,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel MICRA Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel MICRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info