Bedienungsanleitung Satel Versa Plus (Seite 75 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

SATEL VERSA Plus 73

The zones in the system to which the wireless sirens are assigned can be programmed as:

 NC, NO or EOL – provides information about troubles (a trouble causes the zone

violation),

 2EOL/NC or 2EOL/NO – provides information about troubles (a trouble causes the zone

violation) and about tamper.

The type of zones to which the wireless siren is assigned should be matched to the

information sent:

ASP-100 – first zone: low battery; second zone: tamper.

ASP-105 – first zone: low battery and tamper; second zone: external 12 V DC power loss

and tamper.

ASP-205 – both zones: low battery and tamper.

The tamper information is sent immediately, while the trouble information:

ASP-100 – during periodical transmission, which is sent every 15 minutes,

ASP-105 / ASP-205 – during polling.

Tamper alarm on opening the tamper switch in the siren:

ASP-100 – lasts for the maximum duration of signaling programmed for the siren (sound type

selected during programming and optical signaling);

ASP-105 – lasts for the maximum duration of acoustic signaling programmed for the siren

(sound type selected during programming and optical signaling);

ASP-205 – lasts 3 minutes (sound type 1 and optical signaling).

Tamper signaling is blocked:

 when the control panel is running in service mode,

 when the ABAX system is running in test mode (ASP-105 and ASP-205),

 for 10 minutes after connecting the battery (ASP-100),

 for 40 seconds after power-on (ASP-105) / installing the battery (ASP-205).

It enables installation work to be carried out. Opening the tamper switch will not trigger

loud signaling, but information on tamper will be sent (when in service mode, the

control panel will not signal the tamper alarms). The command to block/unblock the

signaling connected with starting / ending the test mode or the service mode is sent

during the response time.

Wireless expanders of hardwired zones and outputs

The wireless expander of hardwired zones and outputs (ACX-200 or ACX-201) takes up 4

zones and 4 outputs in the system. The alarm system zone / output to which the zone /

output in ACX-200 or ACX-201 expander is assigned is programmed in the same way as the

other hardwired zones / outputs of the control panel. You should remember however that

sensitivity of the expander zones may be different from that programmed in the control panel:

– from 20 ms to 140 ms – the same as the value programmed in the control panel,

– above 140 ms – only some values are available: 300 ms, 500 ms, 700 ms, etc. every

200 ms (the programmed value is rounded up to that supported by the expander).

The EN50131-3 standard requires that zones must react to signals lasting more than

400 ms. It means in case of the wireless expanders of hardwired zones and outputs

that no values exceeding 300 ms should be entered when programming the sensitivity

(the higher the value, the lower the sensitivity).

The expander informs you about the zone status as it changes. Also the expander outputs

are controlled in real time. Only the programming of zones takes place during the response

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info