Bedienungsanleitung Satel Versa Plus (Seite 76 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

74 VERSA Plus SATEL

time (in one period, data relating to configuration of one zone are sent to the expander

module, i.e. sending the information on settings of four zones require four response periods).

If communication with the controller is lost, all previously activated outputs will be

deactivated after 20 response periods.

Additionally, the ACX-201 expander module sends information about:

 status of AUX1 and AUX2 power supply outputs – information on overload is sent when

the AUX1 or AUX2 output load exceeds 0.5 A.

 battery status – information on low battery is sent when the battery voltage drops below

11 V for more than 12 minutes (3 battery tests). The expander will kept sending this

information to the controller until the battery voltage rises and remains above 11 V for

longer than 12 minutes (3 battery tests).

 AC power status – information on the loss of power supply is sent when the AC power loss

lasts for more than 30 seconds. The AC power restore is reported with the same delay.

Low battery information for the first zone of ACX-201 expander indicates overload of the

AUX1 or AUX2 power supply output, for the second zone – discharged battery, for the third

zone – loss of AC power.

230 V AC wireless controllers

Activation of the output to which the controller is assigned will result in energizing the

230 V AC electrical circuit (if reverse polarity of the output has been programmed, the circuit

will be deenergized).

Depending on the operating mode, information on the button status (mode 0) or on the

electric circuit status (mode 1 and mode 2) is sent to the zone to which the controller is

assigned. Information on the button status is sent in real time. Information on the electric

circuit status is sent during the response time. Pressing the button / closing the electric circuit

means violation of the zone to which the controller is assigned.

9.5 433 MHz wireless system controller

9.5.1 Presence control of 433 MHz wireless detectors

Presence control – if this option is enabled, the detector is checked for presence. If no

transmission is received from the detector within an hour, trouble will be reported (loss of

communication with the detector).

9.5.2 Configuring the 433 MHz wireless detectors

DLOADX program

You can enable/disable the presence control option: “VERSA – Structure” window

“Hardware” tab “Expansion modules” branch [VERSA-MCU controller name]. Before

making any changes, click on the “Read” button, and after making the changes – on the

“Write” button (the data relating to the 433 MHz wireless detectors are not read after clicking

on the button or saved after clicking on the button in the DLOADX program main

menu). To enable / disable the option, click on the “Presence contr.” column (symbol X

indicates that the option is enabled).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info