Bedienungsanleitung Scan DSA 12 (Seite 14 von 20) (Englisch)

745587

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

INSTRUCTION FOR USE

Primary air

The primary air regulation mechanism is used for lighting the fire, or

to boost the burning process when you put wood on. The primary air

vent can be 0-50% open if you use hard wood fuel such as oak and

beech. You can close the primary air vent if you use soft wood such

as birch or pine for fuel.

Settings for normal load: 0 - 50%

Secondary air

Secondary air is pre-heated and fed indirectly to the fire. At the same

time, the secondary airflow cleans the glass pane to avoid soot build-

up. If you over-restrict the secondary airflow, soot can build up on the

glass pane. The secondary airflow determines the heat output from

your wood stove.

Settings for normal load: 40 - 70%

Ash drawer

Open the glass door to access the ash drawer which is located below

the combustion chamber.

Keep the ash drawer closed at all times when the wood stove is lit.

The ash drawer must not be overfilled and must therefore be emp-

tied at regular intervals.

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\DSA 12\90085005.idw

90085005

Brændkammer, spjæld og askeskuffe

09-06-2011

Scan DSA 12

VÆGT:

AREAL:

N/A

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg

TG.NR:EMNE:

C:\Working Folder\Designs\DSA 12\90085005.idw

90085005

Brændkammer, spjæld og askeskuffe

09-06-2011

Scan DSA 12

VÆGT:

AREAL:

N/A

CB-technique (Clean Burning)

The stove is equipped with the clean burning technique. In order to

ensure an optimal combustion of released gases under the incinera-

tion process, air will pass through a specially developed canal system.

The heated air is led into the combustion chamber through the small

holes at the rear of the burn chamber.

This air volume is controlled by the combustion rate and thus cannot

be regulated.

NOTE: The wood must never be placed higher than the tertiary holes

at the rear of the burn chamber (This does not apply at a cold start).

Lower baffle plate

The baffle plate is placed in the upper part of the combustion

chamber. This plate will block the smoke and give it a longer holding

time in the combustion chamber before it goes up the chimney. The

temperature of the flue gases will decrease because it has more time

to release heat from the stove. When sweeping, remove the smoke

deflector plate and read the "Stove maintenance" section. Be aware

that the baffle plates are made from a porous chemical material

which can break easily. You must therefore take care when handling

them. The baffle plates are wearing components and do not entail a

right to claim.

Lower baffle plate

Secondary air

0% - 100%

Adjustment of air supply,

primary and secondary damper

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

TG.NR:

EMNE:

I:\Udvikling\TEGNING\DSA 12\90085007.idw

90085007

Primær og sekundær luftregulering

21-01-10

Scan DSA 12

VÆGT:

AREAL:

N/A

Pin supporting the

baffle plate

CB Technique

Primary air

Ash drawer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan DSA 12 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan DSA 12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info