Bedienungsanleitung Scheppach Basa 5.0 (Seite 26 von 148) (Alle Sprachen)

781468

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Montage

The machine is not completely assembled

for reasons of transport.

Assembly tools:

13 mm fork wrench

5 mm hexagonal socket wrench

(not included in delivery)

Guide pipe

Fig.“2“

The fence plate underneath the sawblade

has been tted in the works.

Before attaching the guide tube, check

the fence plate for tight t.

If necessary, tighten the clamping levers (1).

Fit the steel holding devices for the guide tube at

the lett and right-hand side of the fence plate.

2 cheese head srews M8 x 16

2 washers

2 steel holding devices

Push the gu!de lube mto the holding devices from

the side. Before tightening the hexagon boIts,

check the parallelity of the guide tube with the

table (dimension „x“).

Dimension „x“ must be identical at the front

and at the rear of the table.

Fence

Fig. „3“

• The fence can be used to the Ieft or

the right of the saw band depending

on wone requirements.

Screw together the feace pipe, intermediate plate,

and guide slide (handscrewed). To da this, insert

both threaded screws into the guide slots.

4 washer 6

4 cheese head screws M6x20

• The divider plate to carry the fence is

screwed onto the fence pipe on the

right or the Ieft depending on the work

requirements.

Do not tighten the wing nuts!

2 saucer-head screws M 6 x 75

2 washers 6

2 wing nuts M6

Place fence rail onto the divider plate.

Position 1: for work with a higher contact surface

Position 2: for work with a lower contact surface

Place the cam lever on the guide slide horizontally.

Place the guide slide onto the guide pipe and push

the cam lever down - c!amp.

On the guide pipe, the upper scale applies to

position 1; the Iower scale to position 2.

Fence adjustment

Fig.“4“

Place the fence on the guide rail.

Place a straight strip on the sawband running

upwards and downwards.

Place an angle on the strip and on the fence.

Adjusting the reading glass

Fig.“5“

The guide tube must project over the sawblade to

such an extent that the scale on the guide tube is

positioned directly under the zero mark of the

magnifying glass.

Release the two belts of the magnifying glass and

set the graduation mark precisely above the

zero mark of the scale.

Retighten the bolts of the magnifying glass.

Setting before inital operation

The electrical current supply is interrupted by a

limit switch when the housing lid is opened!

Cutting speeds

Fig. „6“

Band saw are quipped with 2 cutting speed.

IMPORTANT!

The cutting speed may only be set while the

machine is at a full stop. Pull the mains plug!

Two levels

460 m/min. for wood and hardwood

775 m/min. for soft wood

V-belt 10 x 1072 mm

Cutting speed - levels I - II

463 m/min. 1 to 3

775 m/min. 2 to 4

The machine is delivered with apre-set

cutting speed of 775 m/min for wood and hard-

wood

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Basa 5.0 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info