Bedienungsanleitung Scheppach Basa 5.0 (Seite 28 von 148) (Alle Sprachen)

781468

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Sawbench

Fig.“13“

The saw bench is set at the factory.

The continuous saw bench swing range reaches

trom + 47° to - 20°.

The greatest swing range allows 45° mitered cuts.

The setting must be carried out while the ma-

chine is at a tull stop!

One can readjust the bench at a 90° angle to the

sawband using the setting screw (1) under the

bench. (Use a square as an aid)!

Table adjustment to + 47°

• Loosen both lock levers (2).

• Tum the handle (3) clockwise.

• Re-tighten the lock handles (2) in the

desired position according to the scale.

Table adjustment to - 20°

• Loosen both lock levers (2).

• Tum the handle (3) one quarter revolution

to the right and swing the adjustment

screw (1) on the ball handle to the lett.

• Tum the handle (3) counterclockwise.

• Re-tighten the lock handles (2) in the

desired position according to the scale.

Test the exact angle setting of the table with a

sampie piece before beginning work.

Parallel alignment of the sawband

to the saw bench

Fig. „14“

Exact parallel alignment is especially important

for work with the traverse cutting gauge special

accessory.

Check parallel alignment with the fence rail and a

low angle.

Place the fence rail on the saw band running

upwards and downwards. Place the low angle

on the fence rail as weil as along the longitudinal

groove.

If there are deviations, loosen the 8 hexagonal

nuts of the table attachment swinging segment and

readjust the saw bench appropriately.

Re-tighten the hexagonal nuts rmly!

Set-Up

Prepare the workplace where the machine is to be

placed. Insure sufcient room to allow safe work

without malfunctions. The machine is designed to

operate in closed rooms and must be placed

stabily on rm level ground. Stability is insured by

attachment to the ground with 4 screws.

At least 2 persons are required to lower the

machine from the pallet. Starting in the working

position, tip the machine to the left and pull out the

pallet to the right.

Working information

The following recommendations are examples

of the safe use of band saws.

The following safe working methods should be

seen as an aid to safety. They cannot be applied

suitably completely or comprehensively to every

use. They cannot treat every possible dangerous

condition and must be interpreted carefully.

• Connect the machine to a suction unit when

working in closed rooms. A suction device which

conforms with commercial regulations must be

used for suction in commercial areas.

• Loosen the sawband when the machine is not in

operation (e.g. after nishing work). Attach a noti-

ce on the tension of the saw band to the machine

for the next user.

• Collect unused sawbands and store them safely

in a dry place. Check for faults (teeth, cracks)

before use. Do not use faulty sawbands!

• Wear suitable gloves when handling sawbands.

• All protective and safety devices must be securely

mounted on the machine before beginning work.

• Never clean the sawband or the sawband guide

with a hand-held brush or scraper while the saw-

band is running. Resin-covered sawbands impair

working safety and must be cleaned regularly.

• For your own protection, wear protective glasses

and hearing protection. Wear a hairnet if you

have long hair. Roll up loose sleeves over the

elbows.

• Always position the sawband guide as near the

workpiece as possible when working.

• Insure sufcient lighting in the work area and

around the machine.

• Always use the fence for straight cuts to keep the

workpiece from tipping or slipping away.

• When working on narrow workpieces with manual

feed, use the push stick.

• For diagonal cuts, place the saw bench in the

appropriate position and guide the workpiece on

the fence.

• To cut dove-tails and dove-tailed tenons or

wedges swing the saw bench to the plus or minus

position. Insure safe workpiece guidance.

• For arced and irregular cuts, push the workpiece

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Basa 5.0 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info