Bedienungsanleitung Scheppach BS2000 Primaster (Seite 25 von 46) (Deutsch, Englisch, Französisch)

782174

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

25GB

6. Technical data

Electro motor 230 - 240 V ~ ,50 Hz

Power S1 250W, S2 30 min 350W

Revolutions 1400 min-1

Saw band length 1400 mm

Saw band width 7 mm

Cutting speed 900 m/min

Passage height 0 - 80 mm

Passage width 200 mm

Table size 300 x 300 mm

Slewing range of the

table 0° bis 45°

Max. size of the

workpiece 400 x 400 x 80 mm

Overall weight 16,5 kg

Subject to technical modications!

* Operating mode S1, continous operation.

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

Noise parameters

The total noise values determined in accordance

with EN 61029.

sound pressure level LpA 77,4 dB(A)

uncertainty KpA 3 dB

sound power level LWA 90,4 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Total vibration values (vector sum - three directions)

determined in accordance with EN 61029.

7. Remaining hazards

The machine has been built using modern technolo-

gy in accordance with recognized safety rules. Some

remaining hazards, however, may still exist.

• Risk of injury for ngers and hands by the rotating

saw band due to improper handling of the work

piece.

• Risk of injury through the hurling work piece due

to improper handling, such as working without the

push stick.

• Risk of damaging your health due to wood dust and

wood chips. Wear personal protective cloth such

as goggles. Use a tting dust extractor.

• Risk of injury due to defective saw band. Regu-

larely check saw band for such defects.

• Risk of injury for ngers and hands while changing

saw band. Wear proper gloves.

• Risk of injury due to starting saw band while

switching on the machine.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Wear only closetting clothes. Remove rings,

bracelets and other jewelry.

• For the safety of long hair, wear a cap or hair net.

Even when all safety measures are taken, some

remaining hazards which are not yet evident may

still be present.

• Remaining hazards can be minimized by follow-

ing the instructions in „General safety instructions“

„Proper Use“ and in the entire operating manual.

8. Attachment and operation

Before starting the equipment

Make sure the machine stands securely, i.e. bolt it

to a workbench or solid base. There are two holes

for this purpose in the machine foot. • The saw table

must be mounted correctly.

• All covers and safety devices have to be properly

tted before the machine is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws etc.

• Before you actuate the On/Off switch, make sure

that the saw blade is correctly tted and that the

machine’s moving parts run smoothly.

• Before you connect the machine to the power

supply, make sure the data on the rating plate is

the same as that for your mains.

Assembly tools

1 engineer’s wrench SW 10/13

1 hexagonal head spanner SW 3

1 hexagonal head spanner SW 4

Tabletop and the mounting angles are not mounted

for reasons of packaging technology.

8.1 Assembly of the table top (Fig.

1+2+3+4+5+5.1.5.2)

1 Remove the wing nut (E), the clamping lever (F),

the two disks and the plate (H). (Fig. 5.1)

2 Remove the 2 knurled nuts (D) and remove the U

bracing (C) from the working table. (Fig. 4)

3 Position the working table (A) over the rear (B)

to the screws. Fasten the working table with the

plate (H), the two disks, the wing nut (E) and

the clamping lever (F) to the machine housing.

Fig. 5.2)

4 Attach the U bracing (C) with 2 countersink screws

M6x16 and knurled nuts (D) at the front of the saw-

ing table. (Fig.3+4)

8.2 Adjusting the table top (Fig. 6)

1 Set the table top to home position and tighten the

wing bolt (E) and the clamp lever (F) rmly.

2 Align the table top parallel to the sawing blade

and tighten the 3 screws. Observe that the sawing

blade is centred in the table inlay.

8.3 Adjusting the table top at the right angle to

the sawing blade(Fig. 5+6)

1 Fully set the belt guide (4) upwards and clamp it

tight.

2 Release the clamping lever (F) and the wing bolt

(E) at the swivelling segment (G).

3 Align the table at the right angle (90°) to the sawing

blade (use back square).

4 Adjust the adjusting screw (I) and lock it with a

nut (J).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS2000 Primaster Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info